DTC B1660/43 Passenger Airbag ON/OFF Indicator Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1660/43 |
|
|

| 1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION |
Turn the ignition switch on (IG).
Check the passenger airbag ON/OFF indicator operation.

| ON/OFF Indicator Illumination | Proceed to |
| Always ON | A |
| OFF | B |
|
| ||||
| A | |
| 2.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
w/ Navigation system:
Check that the connectors are properly connected to the center airbag sensor assembly and the multi-display computer assembly. Also check that the connectors that link the instrument panel wire No. 2 and instrument panel wire are properly connected.
Disconnect the connectors from the center airbag sensor assembly and the multi-display computer assembly. Also disconnect the connectors that link the instrument panel wire No. 2 and instrument panel wire.
Check that the terminals of connectors are not damaged.
w/o Navigation system:
Check that the connectors are properly connected to the center airbag sensor assembly and the hazard switch assembly. Also check that the connectors that link the instrument panel wire No. 2 and instrument panel wire are properly connected.
Disconnect the connectors from the center airbag sensor assembly and the hazard switch assembly. Also disconnect the connectors that link the instrument panel wire No. 2 and instrument panel wire.
Check that the terminals of connectors are not damaged.
|
| ||||
| OK | |
| 3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR |
![]() |
Connect the connectors that link the instrument panel wire No. 2 and instrument panel wire.
w/ Navigation system:
Connect the connector to the multi-display computer assembly.
w/o Navigation system:
Connect the connector to the hazard switch assembly.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Check the passenger airbag ON/OFF indicator operation.
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the connector to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 5.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (OPEN) |
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
w/ Navigation system:
Disconnect the connector from the multi-display computer assembly.
w/o Navigation system:
Disconnect the connector from the hazard switch assembly.
Using SST, connect terminals 23 (PAON) and 17 (P-AB) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E19-8 (PAON) - E19-9 (P-AB) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT) |
![]() |
Disconnect SST from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E19-8 (PAON) - E19-9 (P-AB) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 7.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E19-8 (PAON) - Body ground | Always | 1 MΩ or higher |
| E19-9 (P-AB) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 8.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E19-8 (PAON) - Body ground | Ignition switch on (IG) | Below 1 V |
| E19-9 (P-AB) - Body ground | Ignition switch on (IG) | Below 1 V |
| Result | Proceed to |
| OK (w/ Navigation system) | A |
| OK (w/o Navigation system) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 9.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
w/ Navigation system:
Check that the connectors are properly connected to the center airbag sensor assembly and the multi-display computer assembly. Also check that the connectors that link the instrument panel wire No. 2 and instrument panel wire are properly connected.
Disconnect the connectors from the center airbag sensor assembly and the multi-display computer assembly. Also disconnect the connectors that link the instrument panel wire No. 2 and instrument panel wire.
Check that the terminals of connectors are not damaged.
w/o Navigation system:
Check that the connectors are properly connected to the center airbag sensor assembly and the hazard switch assembly. Also check that the connectors that link the instrument panel wire No. 2 and instrument panel wire are properly connected.
Disconnect the connectors from the center airbag sensor assembly and the hazard switch assembly. Also disconnect the connectors that link the instrument panel wire No. 2 and instrument panel wire.
Check that the terminals of connectors are not damaged.
|
| ||||
| OK | |
| 10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (OPEN) |
Connect the connectors that link the instrument panel wire No. 2 and instrument panel wire.

Using SST, connect terminals 23 (PAON) and 17 (P-AB) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E19-8 (PAON) - E19-9 (P-AB) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT) |
![]() |
Disconnect SST from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E19-8 (PAON) - E19-9 (P-AB) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 12.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E19-8 (PAON) - Body ground | Always | 1 MΩ or higher |
| E19-9 (P-AB) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 13.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E19-8 (PAON) - Body ground | Ignition switch on (IG) | Below 1 V |
| E19-9 (P-AB) - Body ground | Ignition switch on (IG) | Below 1 V |
|
| ||||
| OK | |
| 14.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE) |
![]() |
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E19-1 (B) - Body ground | Ignition switch on (IG) | 10 to 14 V |
|
| ||||
| OK | |
| 15.CHECK PASSENGER AIRBAG ON/OFF INDICATOR |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
w/ Navigation system
Connect the connector to the multi-display computer assembly.
w/o Navigation system
Connect the connector to the hazard switch assembly.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Check the indicator according to the conditions in the table below.
| Tester Connection | Switch Condition | Passenger Airbag ON/OFF Indicator |
| D30-23 (PAON) - Body ground | Ignition switch on (IG) | "ON" comes on |
| D30-17 (P-AB) - Body ground | Ignition switch on (IG) | "OFF" comes on |
| Result | Proceed to |
| OK | A |
| NG (w/ Navigation system) | B |
| NG (w/o Navigation system) | C |
|
| ||||
|
| ||||
| A | |
| 16.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Connect the connector to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 17.CHECK INSTRUMENT PANEL WIRE (OPEN) |
Disconnect the instrument panel wire from the instrument panel wire No. 2.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| ED5-4 (PAON) - ED5-3 (P-AB) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 18.CHECK INSTRUMENT PANEL WIRE (SHORT) |
![]() |
Disconnect the instrument panel wire from the instrument panel wire No. 2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| ED5-4 (PAON) - ED5-3 (P-AB) | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 19.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND) |
![]() |
Disconnect the instrument panel wire from the instrument panel wire No. 2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| ED5-4 (PAON) - Body ground | Always | 1 MΩ or higher |
| ED5-3 (P-AB) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 20.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the instrument panel wire from the instrument panel wire No. 2.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| ED5-4 (PAON) - Body ground | Ignition switch on (IG) | Below 1 V |
| ED5-3 (P-AB) - Body ground | Ignition switch on (IG) | Below 1 V |
|
| ||||
| OK | ||
| ||