Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1424/24    Solar Sensor Circuit (Driver Side)

for Preparation Click here


DESCRIPTION

E107008E01
The solar sensor, which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning AUTO mode. The output voltage from the solar sensor varies in accordance with the amount of sunlight. When the sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The air conditioning amplifier detects changes in the output voltage from the solar sensor.

DTC No.
DTC Detection Condition
Trouble Area
B1424/24
Open or short in driver side solar sensor circuit
  1. Solar sensor
  2. Wire harness between solar sensor and air conditioning amplifier
  3. Wire harness between solar sensor and main body ECU
  4. Air conditioning amplifier

WIRING DIAGRAM


E152698E11


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG) and turn Techstream main switch on.

  1. Select the item below in the Data List, and read the value displayed on Techstream.

    Data List / Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Solar Sensor (D side)
    Driver side solar sensor /
    Min.: 0, Max.: 255
    Driver side solar sensor value increases as brightness increases
    -

    OK:
    The display is as specified in the normal condition column.


    Result:

    Result
    Proceed to
    NG
    A
    OK (Checking from PROBLEM SYMPTOMS TABLE)
    B
    OK (Checking from DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER
A


2.CHECK SOLAR SENSOR (SENSOR POWER INPUT)


    E152686E02
  1. Disconnect the F1 solar sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F1-6 (CLTB) - F1-3 (CLTE)
    Ignition switch off
    Below 1 V
    F1-6 (CLTB) - F1-3 (CLTE)
    Ignition switch on (IG)
    11 to 14 V



OK
Go to step 4
NG


3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR)


    E152676E07
  1. Disconnect the D7 in body ECU connector.

  1. Disconnect the F1 solar sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D7-20 (CLTB) - F1-6 (CLTB)
    Always
    Below 1 Ω
    D7-18 (CLTE) - F1-3 (CLTE)
    Always
    Below 1 Ω
    D7-20 (CLTB) - Body ground
    Always
    10 kΩ or higher
    D7-18 (CLTE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) 

4.CHECK SOLAR SENSOR


    E109215E42
  1. Remove the solar sensor with its connector still connected.

  1. Connect the battery's positive (+) lead to terminal 6 (CLTB) and the negative (-) lead to terminal 3 (CLTE) of the solar sensor.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F1-1 (TSL) - F1-3 (CLTE)
    Sensor is subjected to electric light
    0.8 to 4.3 V
    F1-1 (TSL) - F1-3 (CLTE)
    Sensor is covered with a cloth
    Below 0.8 V

    NOTICE:
    1. The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 6 and positive (+) lead to terminal 3 of the solar sensor.
    2. While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

    HINT:
    1. Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor.
    2. As the inspection light is moved away from the sensor, the voltage increases.



NG
REPLACE SOLAR SENSOR
OK


5.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR - A/C AMPLIFIER)


    E152677E10
  1. Disconnect the F1 solar sensor connector.

  1. Disconnect the D37 air conditioning amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D37-33 (TSD) - F1-1 (TSL)
    Always
    Below 1 Ω
    D37-33 (TSD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER