Home › STEERING › POWER STEERING › POWER STEERING SYSTEM

POWER STEERING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed.
Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Turn the ignition switch off.

  2. Connect Techstream to the DLC3.

  3. Turn the ignition switch on (IG).

  4. Turn Techstream on.

  5. Enter the following menus: Chassis / EMPS / Data List.

  6. According to the display on the tester, read the "Data List".

    EMPS: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Meter Vehicle Velocity
    Vehicle speed from meter:
    Min.: 0 km/h (0 mph)
    Max.: 300 km/h (187.5 mph)
    0 km/h (0 mph)
    Vehicle stopped
    No significant fluctuation
    Vehicle driven at constant speed
    Engine Revolution
    Show the engine revolution:
    Min.: 0 rpm
    Max.: 12800 rpm
    No significant fluctuation
    Engine is running at a constant speed
    Motor Actual Current
    Amount of current to motor:
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    Power steering is in operation
    Command Value Current
    Demanded amount of current to motor:
    Min.: -327.68 A
    Max.: 327.68 A
    Value changes in proportion to steering effort
    Power steering is in operation
    Steering Angle Velocity
    Steering angle speed:
    Min.: -32768°/sec.
    Max.: 32767°/sec.
    Value changes in proportion to steering effort
    Steering wheel is turned
    Thermistor Temperature
    ECU substrate temperature:
    Min.: -40°C
    Max.: 150°C
    -40 to 150°C
    Ignition switch on (IG)
    PIG Power Supply
    Power source voltage to activate motor:
    Min.: 0 V
    Max.: 20.1531 V
    11 to 14 V
    Power steering is in operation
    IG Power Supply
    ECU power source voltage:
    Min.: 0 V
    Max.: 20.1531 V
    11 to 14 V
    Ignition switch on (IG)
    Steering Wheel Torque
    Steering wheel torque:
    Min.: -327.68 Nm
    Max.: 7 Nm
    Value changes in proportion to steering effort
    Ignition switch on (IG) and power steering is in operation
    Motor Rotation Angle
    Motor rotation angle:
    Min.: 0°
    Max.: 1441.77°
    During steering operation, motor rotation angle value changes from 0 to 1441.77°
    Power steering is in operation
    Motor Voltage
    Motor power supply voltage:
    Min.:0 V
    Max.: 45.955 V
    11 to 14 V
    Power steering is in operation
    Motor Terminal Volt(U)
    Motor terminal voltage (U phase):
    Min.: 0 V
    Max.: 46.667 V
    When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
    Engine running and steering wheel is turned
    Motor Terminal Volt(V)
    Motor terminal voltage (V phase):
    Min.: 0 V
    Max.: 46.667 V
    When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
    Engine running and steering wheel is turned
    Motor Terminal Volt(W)
    Motor Terminal voltage (W phase):
    Min.: 0 V
    Max.: 46.667 V
    When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
    Engine running and steering wheel is turned
    IG ON/OFF Times
    Ignition switch ON/OFF number of times after fail detection:
    Min.: 0 times
    Max.: 65535 times
    -
    -
    Motor Overheat Record
    Continuous overheat prevention control record:
    REC or UNREC
    UNREC
    -
    Motor Lo Power Record
    PIG power source voltage drop record:
    REC or UNREC
    UNREC
    -
    Eng Rev Inter Record
    Record of engine revolution signal interruption:
    REC or UNREC
    UNREC
    -
    Spd Sig Invalid Record
    Record of vehicle speed signal invalid:
    REC or UNREC
    UNREC
    -
    Battery Voltage Lo Record
    Battery voltage drop number of times:
    Min.: 0 times
    Max.: 65535 times
    -
    -
    Battery Voltage
    Battery voltage:
    Min.: 0 V
    Max.: 25.5 V
    11 to 14 V
    -
    PS Assist Signal
    Power steering assist signal:
    ON or OFF
    ON: Power steering assist signal is sent
    Ignition switch on (IG) and steering wheel is turned
    OFF: Power steering assist signal is not sent
    No steering load (in neutral position)
    The Number of DTCs
    Number of detected DTCs when freeze frame data stored:
    Min.: 0
    Max.: 255
    -
    -


ACTIVE TEST

HINT:
Using Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Turn the ignition switch off.

  2. Connect Techstream to the DLC3.

  3. Turn the ignition switch on (IG).

  4. Turn Techstream on.

  5. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  6. According to the display on the tester, perform the "Active Test".

    Combination meter: 
    Tester Display
    Test Part
    Control Range
    Control Range
    Indicat. EPS (*1)
    P/S Warning Light
    ON or OFF
    Confirm that Vehicle is Stopped and Engine Idling
    Master Warning (*2)
    Master Warning Light
    ON or OFF
    Confirm that Vehicle is Stopped and Engine Idling
    *1: w/o Multi-information Display
    *2: w/ Multi-information Display