Home › STEERING › POWER STEERING › POWER STEERING SYSTEM

POWER STEERING SYSTEM > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA

NOTICE:
  1. It is difficult to show the specified values (judgment values) clearly because freeze frame data values change significantly due to differences in measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.
  2. Turn the ignition switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using Techstream.

  1. Turn the ignition switch off.

  2. Connect Techstream to the DLC3.

  3. Turn the ignition switch on (IG).

  4. Turn Techstream on.

  5. Check the freeze frame data by following the prompts on the Techstream display. Enter the following menus: Chassis / EMPS / Utility / Freeze Frame Data.

    Power Steering ECU: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Meter Vehicle Velocity
    Vehicle speed from meter:
    Min.: 0 km/h (0 mph)
    Max.: 300 km/h (187.5 mph)
    0 km/h (mph)
    Vehicle stopped
    No significant fluctuation
    Vehicle driven at a constant speed
    Engine Revolution
    Shows the engine speed:
    Min.: 0 rpm
    Max.: 12800 rpm
    No significant fluctuation
    Engine is running at a constant speed
    Motor Actual Current
    Amount of current to motor:
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    Power steering is in operation
    Command Value Current
    Demanded amount of current to motor:
    Min.: -327.68 A
    Max.: 327.68 A
    Value changes in proportion to steering effort
    Power steering is in operation
    Steering Angle Velocity
    Steering angle speed:
    Min.: -32768°/sec.
    Max.: 32767°/sec.
    Value changes in proportion to steering effort
    Steering wheel is turned
    Thermistor Temperature
    ECU substrate temperature:
    Min.: -40°C
    Max.: 150°C
    -40 to 150°C
    Ignition switch on (IG)
    PIG Power Supply
    Power source voltage to activate motor:
    Min.: 0 V
    Max.: 20.1531 V
    11 to 14 V
    Power steering is in operation
    IG Power Supply
    ECU power source voltage:
    Min.: 0 V
    Max.: 20.1531 V
    11 to 14 V
    Ignition switch on (IG)
    Motor Rotation Angle
    Motor rotation angle:
    Min.: 0°
    Max.: 360°
    During steering operation, motor rotation angle value changes from 0 to 360°
    Power steering is in operation
    Motor Voltage
    Motor power supply voltage:
    Min.: 0 V
    Max.: 45.955 V
    11 to 14 V
    Power steering is in operation
    Motor Terminal Volt(U)
    Motor terminal voltage (U phase):
    Min.: 0 V
    Max.: 46.667 V
    When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
    Engine running and steering wheel is turned
    Motor Terminal Volt(V)
    Motor terminal voltage (V phase):
    Min.: 0 V
    Max.: 46.667 V
    When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
    Engine running and steering wheel is turned
    Motor Terminal Volt(W)
    Motor Terminal voltage (W phase):
    Min.: 0 V
    Max.: 46.667 V
    When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
    Engine running and steering wheel is turned
    Battery Voltage
    Battery voltage:
    Min.: 0 V
    Max.: 25.5 V
    11 to 14 V
    -
    PS Assist Signal
    Power steering assist signal:
    ON or OFF
    ON: Power steering assist signal is sent
    Ignition switch on (IG) and steering wheel is turned
    OFF: Power steering assist signal is not sent
    No steering load (in centered position)