Home › ENGINE › 2GR-FE ENGINE MECHANICAL › FRONT CRANKSHAFT OIL SEAL

FRONT CRANKSHAFT OIL SEAL > INSTALLATION

for Preparation Click here



1. INSTALL TIMING CHAIN CASE OIL SEAL


    A124982E04
  1. Apply MP grease to a new oil seal lip.

  1. Using SST and a hammer, tap in the oil seal until its surface is flush with the timing chain cover edge.

    SST
    09223-22010  
    09506-35010  

    NOTICE:
    1. Keep the lip free of foreign matter.
    2. Do not tap the oil seal at an angle.



2. INSTALL CRANKSHAFT PULLEY
  1. Align the pulley set key with the key groove of the pulley, and slide on the pulley.



    A119084E01
  1. Using SST, install the pulley bolt.

    SST
    09213-70011   (09213-70020)
    09330-00021  

    Torque:
    250 N*m{ 2550 kgf*cm , 184 ft.*lbf }



3. INSTALL V-RIBBED BELT


    A162386E01
  1. Install the V-ribbed belt.

  1. Using SST, turn the V-ribbed belt tensioner assembly counterclockwise and remove the bar.

    SST
    09961-00950  



    A139509E01
  1. If it is difficult to install the V-ribbed belt, perform the following procedure:

    1. Put the V-ribbed belt on every pulley except the tensioner pulley as shown in the illustration.

    2. Release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and put the V-ribbed belt on the V-ribbed tensioner assembly pulley.

      NOTICE:
      1. Put the backside of the V-ribbed belt on the V-ribbed belt tensioner assembly pulley and No. 2 idler pulley sub-assembly.
      2. Check that the V-ribbed belt is properly set to each pulley.

    3. After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Confirm that the belt has not slipped out of the grooves on the bottom of the crankshaft pulley by hand.



4. INSTALL FRONT FENDER APRON SEAL RH


    A171853
  1. Install the front fender apron seal RH with the 2 bolts and clip.



5. INSTALL FRONT FENDER LINER RH


    B174752
  1. Install the front fender liner RH with the 5 clips and 7 screws.



    B174750
  1. Install 2 new grommets.

  1. Using a 4 mm hexagon wrench, install the 2 screws.



    B174754
  1. Install the screw and pin hold clip.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



6. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY RH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the front fender side protector from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.



    A176045
  1. Clean the front fender moulding sub-assembly RH. (If reusing the front fender moulding sub-assembly RH)

    1. Using a heat light, heat the front fender moulding sub-assembly RH.

    2. Remove the front fender side protector from the front fender moulding sub-assembly RH.

    3. Wipe off any tape adhesive residue with cleaner.

    4. Install a new front fender side protector to the the front fender moulding sub-assembly RH.



    A176044
  1. Install the front fender moulding sub-assembly RH.

    1. Using a heat light, heat the vehicle body and the front fender moulding sub-assembly.

    2. Remove the release paper from the front fender moulding sub-assembly.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. Engage the 3 clips and install the front fender moulding sub-assembly RH.



    A176043
  1. Using a 4 mm hexagon wrench, install the screw.

  1. Install the clip.



7. INSTALL NO. 1 ENGINE UNDER COVER


    A171855
  1. Install the No. 1 engine under cover with the 6 bolts and 2 clips.



8. INSTALL ENGINE UNDER COVER ASSEMBLY


    A171850
  1. Install the engine under cover assembly with the 4 bolts and 5 clips.



    A171849
  1. Install the engine under cover assembly RR with the 2 bolts.



9. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }