SFI SYSTEM > TERMINALS OF ECM |
| SFI SYSTEM |

| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| D35-1 (+B) - B3-1 (E1) | SB - W-B | Power source of ECM | Ignition switch on (IG) | 9 to 14 V |
| D35-2 (+B2) - B3-1 (E1) | GR - W-B | Power source of ECM | Ignition switch on (IG) | 9 to 14 V |
| D35-3 (BATT) - B3-1 (E1) | R - W-B | Battery (for measuring the battery voltage and for the ECM memory) | Always | 9 to 14 V |
| D35-5 (VPMP) - B3-1 (E1) | W - W-B | Vent valve operation signal (built into pump module) | Ignition switch on (IG) | 9 to 14 V |
| D35-6 (MPMP) - B3-1 (E1) | G - W-B | Vacuum pump operation signal (built into pump module) | Vacuum pump OFF | 0 to 3 V |
| D35-6 (MPMP) - B3-1 (E1) | G - W-B | Vacuum pump operation signal (built into pump module) | Vacuum pump ON | 9 to 14 V |
| D35-7 (+BM) - B3-1 (E1) | L - W-B | Power source of ETCS throttle motor | Always | 9 to 14 V |
| D35-8 (MREL) - B3-1 (E1) | L - W-B | EFI relay operation signal | Ignition switch on (IG) | 9 to 14 V |
| D35-9 (IGSW) - B3-1 (E1) | W - W-B | Ignition switch signal | Ignition switch on (IG) | 9 to 14 V |
| D35-10 (FC) - B3-1 (E1) | P - W-B | C/OPEN relay operation signal (fuel pump control) | Ignition switch on (IG) | 9 to 14 V |
| D35-15 (STP) - B3-1 (E1) | R - W-B | Stop light switch signal | Brake pedal depressed | 7.5 to 14 V |
| D35-15 (STP) - B3-1 (E1) | R - W-B | Stop light switch signal | Brake pedal released | Below 1.5 V |
| D35-16 (ST1-) - B3-1 (E1) | LG - W-B | Stop light switch signal (opposite to STP terminal) | Ignition switch on (IG), Brake pedal depressed | Below 1.5 V |
| D35-16 (ST1-) - B3-1 (E1) | LG - W-B | Stop light switch signal (opposite to STP terminal) | Ignition switch on (IG), Brake pedal released | 7.5 to 14 V |
| D35-17 (ACCR)*2 - B3-1 (E1) | O - W-B | ACC relay control signal | Cranking | Below 1.5 V |
| D35-18 (VPA) - D35-20 (EPA) | GR - SB | Accelerator pedal position sensor signal (for engine control) | Ignition switch on (IG), Accelerator pedal fully released | 0.5 to 1.1 V |
| D35-18 (VPA) - D35-20 (EPA) | GR - SB | Accelerator pedal position sensor signal (for engine control) | Ignition switch on (IG), Accelerator pedal fully depressed | 2.6 to 4.5 V |
| D35-19 (VPA2) - D35-21 (EPA2) | R - V | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch on (IG), Accelerator pedal fully released | 1.2 to 2.0 V |
| D35-19 (VPA2) - D35-21 (EPA2) | R - V | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch on (IG), Accelerator pedal fully depressed | 3.4 to 5.0 V |
| D35-22 (PPMP) - B1-28 (E2) | B - BR | Pressure sensor signal (built into pump module) | Ignition switch on (IG) | 3 to 3.6 V |
| D35-23 (TC) - B3-1 (E1) | L - W-B | Terminal TC of DLC3 | Ignition switch on (IG) | 9 to 14 V |
| D35-26 (VCPA) - D35-20 (EPA) | SB - SB | Power source of accelerator pedal position sensor (for VPA) | Ignition switch on (IG) | 4.5 to 5.0 V |
| D35-27 (VCP2) - D35-21 (EPA2) | LG - V | Power source of accelerator pedal position sensor (for VPA2) | Ignition switch on (IG) | 4.5 to 5.0 V |
| D36-1 (TACH) - B3-1 (E1) | B - W-B | Engine speed signal (for combination meter) | Idling | Pulse generation (see waveform 12) |
| D36-8 (SPD) - B3-1 (E1) | LG - W-B | Vehicle speed signal from combination meter | Ignition switch on (IG), driving wheel rotated slowly | Pulse generation (see waveform 9) |
| D36-30 (W) - B3-1 (E1) | Y - W-B | Malfunction Indicator Lamp (MIL) operation signal | Ignition switch on (IG) | Below 3.0 V |
| D36-30 (W) - B3-1 (E1) | Y - W-B | Malfunction Indicator Lamp (MIL) operation signal | Idling | 9 to 14 V |
| D36-33 (CANH) - B3-1 (E1) | B - W-B | CAN communication circuit | Ignition switch on (IG) | Pulse generation (see waveform 13) |
| D36-34 (CANL) - B3-1 (E1) | W - W-B | CAN communication circuit | Ignition switch on (IG) | Pulse generation (see waveform 14) |
| B3-1 (E1) - Body ground | W-B - - | Earth (ground) circuit of ECM | Always | Below 1 V |
| B3-2 (#10) - B1-7 (E01) B3-3 (#20) - B1-7 (E01) B3-4 (#30) - B1-7 (E01) B3-5 (#40) - B1-7 (E01) B3-6 (#50) - B1-7 (E01) B3-7 (#60) - B1-7 (E01) | L - W-B Y - W-B B - W-B W - W-B R - W-B G - W-B | Fuel injector operation signal | Ignition switch on (IG) | 9 to 14 V |
| B3-2 (#10) - B1-7 (E01) B3-3 (#20) - B1-7 (E01) B3-4 (#30) - B1-7 (E01) B3-5 (#40) - B1-7 (E01) B3-6 (#50) - B1-7 (E01) B3-7 (#60) - B1-7 (E01) | L - W-B Y - W-B B - W-B W - W-B R - W-B G - W-B | Fuel injector operation signal | Idling | Pulse generation (see waveform 3) |
| B2-8 (STAR) - B3-1 (E1) | GR - W-B | Park/neutral position switch signal | Ignition switch on (IG), Shift lever position P or N | 9 to 14 V |
| B3-11 (STA) - B3-1 (E1) | B - W-B | Starter relay operation signal | Cranking | 9 to 14 V |
| B3-12 (STSW)*2 - B3-1 (E1) | P - W-B | Starter relay operation signal | Cranking | 9 to 14 V |
| B3-14 (OC2-) - B3-15 (OC2+) | P - LG | Camshaft timing oil control valve operation signal (Intake side) | Ignition switch on (IG) | Pulse generation (see waveform 1) |
| B3-16 (OC1-) - B3-17 (OC1+) | L - Y | Camshaft timing oil control valve operation signal (Intake side) | Ignition switch on (IG) | Pulse generation (see waveform 1) |
| B3-18 (VV2+) - B3-28 (VV2-) | P - L | Variable valve timing sensor signal (Intake side) | Idling | Pulse generation (see waveform 6) |
| B3-19 (VV1+) - B3-29 (VV1-) | G - R | Variable valve timing sensor signal (Intake side) | Idling | Pulse generation (see waveform 6) |
| B3-21 (NE+) - B3-20 (NE-) | W - B | Crankshaft position sensor signal | Idling | Pulse generation (see waveform 5) |
| B3-23 (EV2+) - B3-22 (EV2-) | L - R | Variable valve timing sensor signal (Exhaust side) | Idling | Pulse generation (see waveform 5) |
| B3-25 (EV1+) - B3-24 (EV1-) | B - W | Variable valve timing sensor signal (Exhaust side) | Idling | Pulse generation (see waveform 5) |
| B3-26 (OE1+) - B3-31 (OE1-) | G - R | Camshaft timing oil control valve operation signal (Intake side) | Ignition switch on (IG) | Pulse generation (see waveform 1) |
| B3-27 (OE2+) - B3-32 (OE2-) | P - W | Camshaft timing oil control valve operation signal (Intake side) | Ignition switch on (IG) | Pulse generation (see waveform 1) |
| B3-30 (FPR) - B3-1 (E1) | G - W-B | Fuel pump control | Cranking | 9 to 14 V |
| Idling | Below 3 V | |||
| B1-1 (HT1B) - B3-1 (E1) | R - W-B | Heated oxygen sensor heater operation signal | Idling | Below 3.0 V |
| B1-1 (HT1B) - B3-1 (E1) | R - W-B | Heated oxygen sensor heater operation signal | Ignition switch on (IG) | 9 to 14 V |
| B1-3 (ACM) - B3-1 (E1) | G - W-B | VSV for active control mount system operation signal | Ignition switch on (IG) | 9 to 14 V |
| B1-4 (M-) - B2-3 (ME01) | L - W-B | Throttle drive motor operation signal (negative terminal) | Idling with warm engine | Pulse generation (see waveform 11) |
| B1-5 (M+) - B2-3 (ME01) | R - W-B | Throttle drive motor operation signal (positive terminal) | Idling with warm engine | Pluse generation (see waveform 10) |
| B1-6 (E02) - Body ground | W-B - - | Earth (ground) circuit of ECM | Always | Below 1 V |
| B1-7 (E01) - Body ground | W-B - - | Earth (ground) circuit of ECM | Always | Below 1 V |
| B1-8 (IGT1) - B3-1 (E1) B1-9 (IGT2) - B3-1 (E1) B1-10 (IGT3) - B3-1 (E1) B1-11 (IGT4) - B3-1 (E1) B1-12 (IGT5) - B3-1 (E1) B1-13 (IGT6) - B3-1 (E1) | Y - W-B P - W-B G - W-B L - W-B B - W-B BR - W-B | Ignition coil with igniter (ignition signal) | Idling | Pulse generation (see waveform 7) |
| B1-17 (GE01) - B3-1 (E1) | - - W-B | Shielded earth (ground) circuit of throttle drive motor | Always | Below 1 V |
| B1-18 (OX1B) - B1-28 (E2) | B - BR | Heated oxygen sensor signal | With engine speed at 2500 rpm for 2 minutes after warming up | Pulse generation (see waveform 2) |
| B1-19 (VTA2) - B1-28 (E2) | LG - BR | Throttle position sensor signal (for sensor malfunction detection) | Ignition switch on (IG), Accelerator pedal fully released | 2.1 to 3.1 V |
| B1-19 (VTA2) - B1-28 (E2) | LG - BR | Throttle position sensor signal (for sensor malfunction detection) | Ignition switch on (IG), Accelerator pedal fully depressed | 4.5 to 5.0 V |
| B1-20 (VTA1) - B1-28 (E2) | B - BR | Throttle position sensor signal (for engine control) | Ignition switch on (IG), Throttle valve fully closed | 0.5 to 1.2 V |
| B1-20 (VTA1) - B1-28 (E2) | B - BR | Throttle position sensor signal (for engine control) | Ignition switch on (IG), Throttle valve fully open | 3.2 to 4.8 V |
| B1-21 (THW) - B1-28 (E2) | W - BR | Engine coolant temperature sensor signal | Idling, Engine coolant temperature 80°C (176°F) | 0.2 to 1.0 V |
| B1-22 (THA) - B1-29 (E2G) | P - Y | Intake air temperature sensor signal | Idling, Intake air temperature 20°C (68°F) | 0.5 to 3.4 V |
| B1-23 (VC) - B1-28 (E2) | R - BR | Power source of sensors (specific voltage) | Ignition switch on (IG) | 4.5 to 5.0 V |
| B1-24 (IGF1) - B3-1 (E1) | W - W-B | Ignition coil with igniter (ignition confirmation signal) | Ignition switch on (IG) | 4.5 to 5.0 V |
| B1-24 (IGF1) - B3-1 (E1) | W - W-B | Ignition coil with igniter (ignition confirmation signal) | Idling | Pulse generation (see waveform 7) |
| B1-27 (AICV) - B3-1 (E1) | W - W-B | VSV for air intake control system operation signal | Ignition switch on (IG) | 9 to 14 V |
| B1-28 (E2) - B3-1 (E1) | BR - W-B | Earth (ground) circuit of sensors for ETCS | Always | Below 1 V |
| B1-29 (E2G) - B3-1 (E1) | Y - W-B | Earth (ground) circuit of sensor for mass air flow meter | Always | Below 1 V |
| B1-30 (VG) - B1-29 (E2G) | R - Y | Mass air flow meter signal | Idling, Shift lever position P or N, A/C switch OFF | 0.5 to 3.0 V |
| B1-33 (ACIS) - B3-1 (E1) | L - W-B | VSV for acoustic control induction system operation signal | Ignition switch on (IG) | 9 to 14 V |
| B1-34 (PRG) - B3-1 (E1) | G - W-B | Purge VSV for EVAP system operation signal | Ignition switch on (IG) | 9 to 14 V |
| B1-34 (PRG) - B3-1 (E1) | G - W-B | Purge VSV for EVAP system operation signal | Idling | Pulse generation (see waveform 8) |
| B2-1 (HA2A) - B2-6 (E05) | B - W-B | Air fuel ratio sensor heater operation signal | Idling | Below 3.0 V |
| B2-1 (HA2A) - B2-6 (E05) | B - W-B | Air fuel ratio sensor heater operation signal | Ignition switch on (IG) | 9 to 14 V |
| B2-2 (HA1A) - B2-7 (E04) | L - W-B | Air fuel ratio sensor heater operation signal | Idling | Below 3.0 V |
| B2-2 (HA1A) - B2-7 (E04) | L - W-B | Air fuel ratio sensor heater operation signal | Ignition switch on (IG) | 9 to 14 V |
| B2-3 (ME01) - B3-1 (E1) | W-B - W-B | Earth (ground) circuit of ECM | Always | Below 1 V |
| B2-4 (E03) - B3-1 (E1) | W-B - W-B | Earth (ground) circuit of ECM | Always | Below 1 V |
| B2-5 (HT2B) - B3-1 (E1) | R - W-B | Heated oxygen sensor heater operation signal | Idling | Below 3.0 V |
| B2-5 (HT2B) - B3-1 (E1) | R - W-B | Heated oxygen sensor heater operation signal | Ignition switch on (IG) | 9 to 14 V |
| B2-6 (E05) - B3-1 (E1) | W-B - W-B | Earth (ground) circuit of ECM | Always | Below 1 V |
| B2-7 (E04) - B3-1 (E1) | W-B - W-B | Earth (ground) circuit of ECM | Always | Below 1 V |
| B2-21 (KNK2) - B2-20 (EKN2) | R - G | Knock sensor signal | With engine speed at 4000 rpm after warming up | Pulse generation (see waveform 4) |
| B2-22 (A1A+) - B3-1 (E1) | BR - W-B | Air fuel ratio sensor signal | Ignition switch on (IG) | 3.3 V*1
|
| B2-23 (A2A+) - B3-1 (E1) | P - W-B | Air fuel ratio sensor signal | Ignition switch on (IG) | 3.3 V*1
|
| B2-29 (KNK1) - B2-28 (EKNK) | B - W | Knock sensor signal | With engine speed at 4000 rpm after warming up | Pulse generation (see waveform 4) |
| B2-30 (A1A-) - B3-1 (E1) | Y - W-B | Air fuel ratio sensor | Ignition switch on (IG) | 3.0 V*1
|
| B2-31 (A2A-) - B3-1 (E1) | L - W-B | Air fuel ratio sensor | Ignition switch on (IG) | 3.0 V*1
|
| B2-33 (OX2B) - B1-28 (E2) | B - BR | Heated oxygen sensor signal | With engine speed at 2500 rpm for 2 minutes after warming up | Pulse generation (see waveform 2) |
![]() |
WAVEFORM 1
Camshaft timing oil control valve operation signal
| ECM Terminal Names | Between OC1+ and OC1- , OC2+ and OC2- , OE1+ and OE1- , or OE2+ and OE2- |
| Tester Ranges | 5 V/DIV, 1 msec./DIV |
| Conditions | Idling |
![]() |
WAVEFORM 2
Heated oxygen sensor signal
| ECM Terminal Names | Between OX1B and E2, or OX2B and E2 |
| Tester Ranges | 0.2 V/DIV, 200 msec./DIV |
| Conditions | With engine speed at 2500 rpm for 2 minutes after warming up |
![]() |
WAVEFORM 3
Fuel injector operation signal
| ECM Terminal Names | Between #10 (to 60) and E01 |
| Tester Ranges | 30 V/DIV, 20 msec./DIV |
| Conditions | Idling |
![]() |
WAVEFORM 4
Knock sensor signal
| ECM Terminal Names | Between KNK1 and EKNK, or KNK2 and EKN2 |
| Tester Ranges | 0.01 to 10 V/DIV, 0.01 to 10 msec./DIV |
| Conditions | With engine speed at 4000 rpm after warming up |
![]() |
WAVEFORM 5
Variable Valve Timing (VVT) sensor signal (1)
Crankshaft position sensor signal (2)
| ECM Terminal Names | (1) EV1+ and EV1-, or EV2+ and EV2- (2) Between NE+ and NE- |
| Tester Ranges | 5 V/DIV, 20 ms./DIV |
| Conditions | Idling |
![]() |
WAVEFORM 6
Variable Valve Timing (VVT) sensor signal (1)
Crankshaft position sensor signal (2)
| ECM Terminal Names | (1) Between VV1+ and VV1-, VV2+and VV2- (2) Between NE+ and NE- |
| Tester Ranges | 5 V/DIV, 20 ms./DIV |
| Conditions | Idling |
![]() |
WAVEFORM 7
Igniter IGT signal (from ECM to igniter) (1)
Igniter IGF signal (from igniter to ECM) (2)
| ECM Terminal Names | (1) Between IGT (1 to 6) and E1 (2) Between IGF1 and E1 |
| Tester Ranges | 2 V/DIV, 20 msec./DIV |
| Conditions | Idling |
![]() |
WAVEFORM 8
Purge VSV for EVAP system operation signal
| ECM Terminal Names | Between PRG and E1 |
| Tester Ranges | 10 V/DIV, 50 msec./DIV |
| Conditions | Idling |
![]() |
WAVEFORM 9
Vehicle speed signal
| ECM Terminal Names | Between SPD and E1 |
| Tester Ranges | 2 V/DIV, 20 msec./DIV |
| Conditions | Driving at 12 mph (20 km/h) |
![]() |
WAVEFORM 10
Throttle drive motor operation signal (positive terminal)
| ECM Terminal Names | Between M+ and ME01 |
| Tester Ranges | 5 V/DIV, 1 msec./DIV |
| Conditions | Idling with warm engine |
![]() |
WAVEFORM 11
Throttle drive motor operation signal (negative terminal)
| ECM Terminal Names | Between M- and ME01 |
| Tester Ranges | 5 V/DIV, 1 msec./DIV |
| Conditions | Idling with warm engine |
![]() |
WAVEFORM 12
Engine speed signal
| ECM Terminal Names | Between TACH and E1 |
| Tester Ranges | 5 V/DIV, 10 msec./DIV |
| Conditions | Idling |
![]() |
WAVEFORM 13
CAN communication signal
| ECM Terminal Name | Between CANH and E1 |
| Tester Range | 1 V/DIV., 10 μs./DIV. |
| Condition | Engine stopped engine and ignition switch on (IG) |
![]() |
WAVEFORM 14
CAN communication signal
| ECM Terminal Name | Between CANL and E1 |
| Tester Range | 1 V/DIV., 10 μs./DIV. |
| Condition | Engine stopped and ignition switch on (IG) |