Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0121    Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem

for Preparation Click here

HINT:
This DTC relates to the throttle position sensor.


DESCRIPTION

Refer to DTC P0120 .

DTC No.
DTC Detection Condition
Trouble Area
P0121
Difference between VTA1 and VTA2 voltages less than 0.8 V, or more than 1.6 V for 2 seconds (1 trip detection logic)
Throttle position sensor (built into throttle body)

MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle.
This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm the proper operation of the throttle position sensor and VTA1.
For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the voltage output difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction of the throttle position sensor. The ECM illuminates the MIL and sets the DTC.
If the malfunction is not repaired successfully, the DTC is set 2 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0121: Throttle position sensor rationality
Required Sensors / Components (Main)
Throttle position sensor
Required Sensors / Components (Related)
-
Frequency of Operation
Continuous
Duration
Within 2 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


This monitor will not run whenever these DTCs are not present
None
Either of the following conditions is met:
Condition 1 or 2
1. Ignition switch
ON (IG)
2. Electric throttle motor power
ON
Throttle position sensor malfunction (P0120, P0122, P0123, P0220, P0222, P0223, P2135)
Not detected

TYPICAL MALFUNCTION THRESHOLDS


Difference of throttle position sensor voltage between VTA1 and VTA2 x 0.8
Less than 0.8 V, or more than 1.6 V

FAIL-SAFE

When this DTC, as well as other DTCs relating to electronic throttle control system malfunctions, is set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed slowly, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC P0121)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTC.

    Result:

    Display (DTC output)
    Proceed to
    P0121
    A
    P0121 and other DTCs
    B

    HINT:
    If any DTCs other than P0121 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A

REPLACE THROTTLE BODY (Click here)