Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0101    Mass or Volume Air Flow Circuit Range / Performance Problem

for Preparation Click here


DESCRIPTION

Refer to DTC P0100 .

DTC No.
DTC Detection Condition
Trouble Area
P0101
Conditions (a), (b), (c), (d) and (e) continue for more than 10 seconds (2 trip detection logic):
(a) Engine running
(b) Engine coolant temperature 70°C (158°F) or higher
(c) Throttle Position (TP) sensor voltage 0.24 V or more
(d) Average engine load value ratio less than 0.85, or more than 1.39 (varies with estimated engine load)
Average engine load value ratio = Average engine load based on MAF meter output / Average engine load estimated from driving conditions
(e) Average air-fuel ratio less than -20%, or more than 20%
  1. Mass Air Flow (MAF) meter
  2. Air induction system
  3. PCV hose connections

MONITOR DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection time and to provide an appropriate air fuel ratio.
Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air. By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, changing their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components of the mass air flow meter. The voltage level is proportional to the air flow through the sensor, and the ECM uses it to calculate the intake air volume.
If there is a defect in the sensor, or an open or short in the circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter and sets the DTC.
Example:
  1. If the voltage is more than 2.2 V, or less than 0.73 V while idling, the ECM determines that there is a malfunction in the mass air flow meter and sets the DTC.

MONITOR STRATEGY


Related DTCs
P0101: Mass air flow meter rationality
Required Sensors / Components (Main)
Mass air flow meter
Required Sensors / Components (Related)
Crankshaft position sensor, engine coolant temperature sensor and throttle position sensor
Frequency of Operation
Continuous
Duration
10 times
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
None
Throttle position (Throttle position sensor voltage)
0.24 V or more
Engine
Running
Battery voltage
10.5 V or more
Engine coolant temperature
70°C (158°F) or more
Intake air temperature sensor current (P0110, P0112)
OK
Engine coolant temperature sensor current (P0115, P0117, P0118)
OK
Crankshaft position sensor current (P0335)
OK
Throttle position sensor current (P0120, P0121, P0122, P0123)
OK
Fuel tank pressure sensor (P0452, P0453)
OK
EVAP leak detection pump (P2401, P2402)
OK
EVAP vent valve (P2419, P2420)
OK

TYPICAL MALFUNCTION THRESHOLDS


Both of following conditions 1 and 2 met
-
1. Averaged engine load value ratio
Less than 0.85, or more than 1.39 (varies with estimated engine load)
2. Averaged air-fuel ratio
Less than -20%, or more than 20%

WIRING DIAGRAM

Refer to DTC P0100 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0101)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0101 and other DTCs
    A
    P0101
    B

    HINT:
    If any DTCs other than P0101 are output, troubleshoot those DTCs first.



B
REPLACE MASS AIR FLOW METER (Click here)
A

GO TO DTC CHART (Click here)