Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0505    Idle Control System Malfunction

for Preparation Click here


DESCRIPTION

The idling speed is controlled by the electronic throttle control system. The electronic throttle control system is comprised of: 1) the one valve type throttle body; 2) the throttle actuator, which operates the throttle valve; 3) the throttle position sensor, which detects the opening angle of the throttle valve; 4) the accelerator pedal position sensor, which detects the accelerator pedal position; and 5) the ECM, which controls the electronic throttle control system.
Based on the target idling speed, the ECM controls the throttle actuator to provide the proper throttle valve opening angle.

DTC No.
DTC Detection Condition
Trouble Area
P0505
Idling speed continues to vary greatly from target idling speed (2 trip detection logic)
  1. Electronic throttle control system
  2. Intake system
  3. PCV hose connection
  4. ECM

MONITOR DESCRIPTION

The ECM monitors the idling speed and idling air flow volume to conduct Idle Speed Control (ISC). The ECM determines that the ISC system is malfunctioning if the following conditions are met:
  1. The learned idling air flow volume remains at the maximum or minimum volume 5 times or more in a drive cycle.
  2. After driving at 10 km/h (6 mph) or more, the actual engine idling speed varies from the target idling speed by between 100 rpm and 200 rpm, 5 times or more in a drive cycle.
Example:

  1. If the actual idling speed varies from the target idling speed by more than 200 rpm* 5 times in a drive cycle, the ECM illuminates the MIL and sets the DTC.
    *: Threshold idling speed varies according to the engine load.


    A082389E22


MONITOR STRATEGY


Related DTCs
P0505: ISC Function
Required Sensors / Components (Main)
Electronic throttle control system
Required Sensors / Components (Related)
Crankshaft position sensor, Engine coolant temperature sensor, and Vehicle speed sensor
Frequency of Operation
Continuous
Duration
10 minutes
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
P0010, P0020 (OCV bank 1, 2)
P0011, P0021 (VVT system bank 1, 2 - advance)
P0012, P0022 (VVT system bank 1, 2 - retard)
P0013, P0023 (Exhaust OCV bank 1, 2)
P0014, P0024 (Exhaust VVT system bank 1, 2 - advance)
P0015, P0025 (Exhaust VVT system bank 1, 2 - retard)
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052 (A/F sensor heater)
P0100, P0102, P0103 (MAF meter)
P0115, P0117, P0118 (ECT sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP sensor)
P0125 (Insufficient ECT for closed loop)
P0171, P0172, P0174, P0175 (Fuel system)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (CKP sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0450, P0451, P0452, P0453 (EVAP system)
P0500 (Vehicle speed sensor)
P2195, P2196, P2197, P2198 (A/F sensor - rationality)
P2237, P2240 (A/F sensor - open)
P2238, P2241, P2252, P2255 (A/F sensor - low impedance)
P2239, P2242, P2253, P2256 (A/F sensor - high impedance)
P2A00, P2A03 (A/F sensor - slow response)
Engine
Running

TYPICAL MALFUNCTION THRESHOLDS


Either of following conditions is met
Condition 1 or 2
1. Frequency that both of the following conditions (a) and (b) met
5 times or more
(a) Engine RPM - target engine RPM
Below -100 rpm, or 150 rpm or more
(b) Vehicle condition
Stop after vehicle was driven by 6.25 mph (10.06 km/h) or more
2. Frequency that both of the following conditions (a) and (b) are met
Once
(a) Engine RPM - target engine RPM
Below -100 rpm, or 150 rpm or more
(b) IAC flow rate learning valve
1.3 L/sec. or less, or 8.5 L/sec. or more

INSPECTION PROCEDURE

HINT:
  1. The following conditions may also cause DTC P0505 to be set:
    1. The floor carpet overlapping slightly onto the accelerator pedal, causing the accelerator pedal to be slightly depressed and therefore the throttle valve position to be slightly open.
    2. The accelerator pedal being not fully released.
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0505)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0505
    A
    P0505 and other DTCs
    B

    HINT:
    If any DTCs other than P0505 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leakage.

    OK:
    No leakage from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


4.CHECK THROTTLE VALVE
  1. Check the throttle valve condition.

    OK:
    No foreign objects between the throttle valve and housing.



NG
REPLACE THROTTLE BODY (Click here)
OK

REPLACE ECM (Click here)