Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0504    Brake Switch "A" / "B" Correlation

DTC    P0724    Brake Switch "B" Circuit High

for Preparation Click here


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed or released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.

HINT:
The normal conditions are as shown in the table below. The signals can be read using the Techstream.

Signals
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF


DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch on (IG)
(b) Brake pedal released
(c) STP signal OFF when ST1- signal OFF
  1. Short in stop light switch signal circuit
  2. STOP fuse
  3. Stop light switch
  4. ECM
P0724
The stop light switch remains ON even when the vehicle is driven in a STOP (less than 2 mph (3 km/h)) and GO (19 mph (30 km/h) or more) fashion 5 times. (2 trip detection logic)
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains ON during "stop and go" driving, the ECM interprets this as a fault in the stop light switch and the MIL comes on and the ECM stores the DTC. The vehicle must stop (less than 2 mph (3 km/h)) and go (19 mph (30 km/h) or more) 5 times for two driving cycles in order to detect a malfunction.

MONITOR STRATEGY


Related DTCs
P0724: Stop light switch/Rationality
Required sensors/Components
Stop light switch, Vehicle speed sensor
Frequency of operation
Continuous
Duration
GO and STOP 5 times
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever this DTC is not present
None
Ignition switch
on (IG)
Starter
OFF
Battery voltage
8 V or more
GO (Vehicle speed is 18.65 mph (30 km/h) or more)
Once
STOP (Vehicle speed is less than 1.86 mph (3 km/h))
Once

TYPICAL MALFUNCTION THRESHOLDS


Switch status ON stuck
Remain ON during GO and STOP 5 times

WIRING DIAGRAM


A172773E01


A141115E07


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK OPERATION OF STOP LIGHT
  1. Check whether the stop lights turn on and off normally when the brake pedal is depressed and released.

    OK:
    Stop lights turn on when brake pedal is depressed.



NG
GO TO LIGHTING SYSTEM (STOP LIGHT SYSTEM) (Click here)
OK


2.INSPECT STOP LIGHT SWITCH ASSEMBLY


    A072924E24
  1. Remove the stop light switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Switch Position
    Tester Connection
    Specified Condition
    Switch pin free
    1 - 2
    Below 1 Ω
    Switch pin free
    3 - 4
    10 kΩ or higher
    Switch pin pushed in
    1 - 2
    10 kΩ or higher
    Switch pin pushed in
    3 - 4
    Below 1 Ω

  1. Reinstall the stop light switch assembly.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


3.READ VALUE USING TECHSTREAM (STP SIGNAL AND ST1 - VOLTAGE)


    G035663E15
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light Switch.

  1. Check the STP signal when the brake pedal is depressed and released.

    Standard:
    Brake Pedal Operation
    Specified Condition
    Depressed
    STP signal ON
    Released
    STP signal OFF

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Brake Pedal Operation
    Specified Condition
    D35-16 (ST1-) - B3-1 (E1)
    Depressed
    Below 1.5 V
    D35-16 (ST1-) - B3-1 (E1)
    Released
    7.5 to 14 V



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)


    A168215E04
  1. Disconnect the stop light switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Check for open:
    Tester Connection
    Condition
    Specified Condition
    A19-1 (Stop light switch) - D35-15 (STP)
    Always
    Below 1 Ω
    A19-4 (Stop light switch) - D35-16 (ST1-)
    Always
    Below 1 Ω
    Check for short:
    Tester Connection
    Condition
    Specified Condition
    A19-1 (Stop light switch) or D35-15 (STP) - Body ground
    Always
    10 kΩ or higher
    A19-4 (Stop light switch) or D35-16 (ST1-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the stop light switch connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH - ECM)
OK

REPLACE ECM (Click here)