Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2102    Throttle Actuator Control Motor Circuit Low

DTC    P2103    Throttle Actuator Control Motor Circuit High

for Preparation Click here


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.
The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:
This electronic throttle control system does not use a throttle cable.


DTC No.
DTC Detection Condition
Trouble Area
P2102
Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
(a) Throttle actuator duty ratio exceeds 80% or more
(b) Throttle actuator current is 0.5 A or less
  1. Open in throttle actuator circuit
  2. Throttle actuator
  3. ECM
P2103
Either of the following conditions is met:
  1. Hybrid IC diagnosis signal fails
  2. Hybrid IC current limiter port fails
  1. Short in throttle actuator circuit
  2. Throttle actuator
  3. Throttle valve
  4. Throttle body
  5. ECM

MONITOR DESCRIPTION

The ECM monitors the electrical current through the electronic actuator, and detects malfunctions and open circuits in the throttle actuator based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the throttle actuator. In addition, if the throttle valve does not function properly (for example, stuck on), the ECM determines that there is a malfunction. The ECM then illuminates the MIL and sets a DTC.
Example:
  1. When the electrical current is more than 10 A, or less than 0.5 A and the throttle actuator duty ratio exceeds 80%, the ECM interprets this as the current being outside the standard range, and illuminates the MIL and sets a DTC.
  2. If the malfunction is not repaired successfully, a DTC is set when the engine is quickly revved up to a high rpm several times after the engine has idled for 5 seconds after engine start.

MONITOR STRATEGY


Related DTCs
P2102: Throttle actuator current (low current)
P2103: Throttle actuator current (high current)
Required Sensors / Components (Main)
Throttle actuator (throttle body)
Required Sensors / Components (Related)
None
Frequency of Operation
Continuous
Duration
P2102: 2 seconds
P2103: 25 times or 0.6 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
The monitor will run whenever these DTCs are not present
None

P2102: 
Throttle motor
ON
Duty-cycle ratio to open throttle actuator
80% or more
Throttle actuator power supply
8 V or more
Motor current change during latest 0.016 sec
Less than 0.2 A

P2103: 
Throttle motor
ON
Either of the following conditions is met:
Condition 1 or 2
1. Throttle actuator power supply
8 V or more
2. Throttle actuator power
ON
Battery voltage
8 V or more
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


P2102: 
Throttle actuator current
Less than 0.5 A

P2103: 
Either of the following conditions is met
Condition 1 or 2
1. Hybrid IC diagnosis signal
Fail
2. Hybrid IC current limiter port
Fail

FAIL-SAFE

When either of these DTCs, as well as other DTCs relating to electronic throttle control system malfunctions, is set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed.
If the accelerator pedal is depressed gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM


G041063E09


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
  2. The throttle actuator current (Throttle motor current) and the throttle actuator duty ratio (Throttle Motor Open Duty / Throttle Motor Close Duty) can be read using the Techstream. However, the ECM shuts off the throttle actuator current when the electronic throttle control system malfunctions.

1.INSPECT THROTTLE BODY (RESISTANCE OF THROTTLE CONTROL MOTOR)


    A159755E06
  1. Disconnect the throttle body connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B27-2 (M+) - B27-1 (M-)
    20°C (68°F)
    0.3 to 100 Ω

  1. Reconnect the throttle body connector.



NG
REPLACE THROTTLE BODY (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)


    A168218E02
  1. Disconnect the throttle body connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Check for open:
    Tester Connection
    Condition
    Specified Condition
    B27-2 (M+) - B1-5 (M+)
    Always
    Below 1 Ω
    B27-1 (M-) - B1-4 (M-)
    Always
    Below 1 Ω
    Check for short:
    Tester Connection
    Condition
    Specified Condition
    B27-2 (M+) or B1-5 (M+) - Body ground
    Always
    10 kΩ or higher
    B27-1 (M-) or B1-4 (M-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle body connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - ECM)
OK


3.INSPECT THROTTLE BODY
  1. Check for foreign objects between the throttle valve and the housing.

    OK:
    Normal



NG
REMOVE FOREIGN OBJECT AND CLEAN THROTTLE BODY
OK


4.INSPECT THROTTLE VALVE
  1. Check if the throttle valve opens and closes smoothly.

    OK:
    The throttle valve opens and closes smoothly.



NG
REPLACE THROTTLE BODY (Click here)
OK

REPLACE ECM (Click here)