Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Active Control Engine Mount System

for Preparation Click here


DESCRIPTION

  1. LOCATION

    A168227E01

The Active Control Engine Mount (ACM) system decreases engine vibration at engine idling using the ACM VSV. The VSV is controlled by a pulse signal transmitted to the VSV from the ECM. The frequency of this pulse signal is matched to the engine speed to decrease engine vibration.

WIRING DIAGRAM


A136867E28


INSPECTION PROCEDURE

1.CHECK VACUUM HOSES


    G042514E04
  1. If the hose is damaged, replace the vacuum hose assembly.

  1. Check the air and vacuum hoses for looseness, disconnection and blockage.



NG
REPAIR OR REPLACE VACUUM HOSES
OK


2.CHECK VACUUM TANK
  1. Check the vacuum tank (Click here).



NG
REPLACE AIR CLEANER CAP
OK


3.INSPECT ECM


    A114640E08
  1. Connect the oscilloscope between terminals ACM and E1 of the ECM connectors.

  1. Warm up the engine to normal operating temperature.

  1. Turn the A/C switch on.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    B1-3 (ACM) - B3-1 (E1)
    Shift position is D, and engine speed is 850 rpm or less
    Pulse generation
    Shift position is D, and engine speed is 950 rpm or more
    9 to 14 V
    Shift position is P
    9 to 14 V



NG
Go to step 6
OK


4.INSPECT DUTY VACUUM SWITCHING VALVE (OPERATION)


    A052014E04
  1. Remove the VSV for ACM.

  1. Check operation of the VSV for ACM when positive battery voltage is applied to the terminals of the VSV for ACM connector.

    Positive battery voltage is not applied:
    The air from pipe G is flowing out through pipes E and H.

    Positive battery voltage is applied:
    The air from pipe F is flowing out through pipes E and H.

  1. Reinstall the VSV for ACM.



NG
REPLACE DUTY VACUUM SWITCHING VALVE (Click here)
OK


5.INSPECT ENGINE MOUNTING INSULATOR ASSEMBLY FRONT


    A051989
  1. Disconnect the vacuum hose from the front engine mount insulator.

  1. Using a vacuum pump, apply vacuum of 80 kPa (600 mmHg, 25 in.Hg) and wait for 1 minute.

  1. Check that there is no change in the needle movement of the vacuum pump gauge.

  1. Check that there is no fluid leakage caused by a break in the diaphragm.

    OK:
    Vacuum pressure exists.

  1. Reconnect the vacuum hose.



NG
REPLACE ENGINE MOUNTING INSULATOR ASSEMBLY FRONT (Click here)
OK

SYSTEM OK 

6.INSPECT DUTY VACUUM SWITCHING VALVE (RESISTANCE)


    A172714E01
  1. Disconnect the VSV for ACM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    19 to 21 Ω

  1. Reconnect the VSV for ACM connector.



NG
REPLACE DUTY VACUUM SWITCHING VALVE (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (VSV FOR ACM - ECM)


    A168244E02
  1. Disconnect the VSV for ACM connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Check for open:
    Tester Connection
    Condition
    Specified Condition
    B8-2 - B1-3 (ACM)
    Always
    Below 1 Ω
    Check for open:
    Tester Connection
    Condition
    Specified Condition
    B8-2 or B1-3 (ACM) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the VSV connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (VSV FOR ACM - ECM)
OK


8.INSPECT FUSE (EFI NO. 3 FUSE)


    A168235E02
  1. Remove the EFI No. 3 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    EFI No. 3 fuse
    Always
    Below 1 Ω

  1. Reinstall the EFI No. 3 fuse.



NG
REPLACE FUSE (EFI NO. 3 FUSE)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI NO. 3 FUSE - VSV FOR ACM)