POWER BACK DOOR SYSTEM > TERMINALS OF ECU |
| CHECK POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) |

Disconnect the O15 ECU connector.
Measure the voltage and resistance according to the value(s) in the table below:
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| O15-10 (ECUB) - Body ground | BR - Body ground | ECUB power supply | Always | 10 to 14 V |
| O15-12 (B) - Body ground | B - Body ground | B power supply | Always | 10 to 14 V |
| O15-8 (IG) - Body ground | GR - Body ground | IG power supply | Ignition switch on (IG) | 10 to 14 V |
| O15-8 (IG) - Body ground | GR - Body ground | IG power supply | Ignition switch off | Below 1 V |
| O15-17 (MSW) - Body ground | V - Body ground | Power back door main switch signal circuit | Power back door main switch not pushed | Below 1 Ω |
| O15-17 (MSW) - Body ground | V - Body ground | Power back door main switch signal circuit | Power back door main switch pushed | 10 kΩ or higher |
| O15-20 (FUL) - Body ground | LG - Body ground | Back door courtesy light switch signal circuit | Back door is opened | Below 1 Ω |
| O15-20 (FUL) - Body ground | LG - Body ground | Back door courtesy light switch signal circuit | Back door is closed | 10 kΩ or higher |
| O15-4 (DS1) - Body ground | P - Body ground | Back door closer switch signal circuit | Back door closer switch ON | Below 1 Ω |
| O15-4 (DS1) - Body ground | P - Body ground | Back door closer switch signal circuit | Back door closer switch OFF | 10 kΩ or higher |
| O15-15 (OSL) - O15-14 (OSE) | GR - Y | Power back door touch sensor LH circuit | Back door touch sensor LH not pressed | Approx. 1 kΩ |
| O15-15 (OSL) - O15-14 (OSE) | GR - Y | Power back door touch sensor LH circuit | Back door touch sensor LH pressed | Below 100 Ω |
| O15-13 (OSR) - O15-14 (OSE) | G - Y | Power back door touch sensor RH circuit | Back door touch sensor RH not pressed | Approx. 1 kΩ |
| O15-13 (OSR) - O15-14 (OSE) | G - Y | Power back door touch sensor RH circuit | Back door touch sensor RH pressed | Below 100 Ω |
| O15-11 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the O15 ECU connector.
Measure the voltage according to the value(s) in the table below:
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| O15-26 (BZR+) - Body ground | B - Body ground | Power back door warning buzzer signal input | Back door warning buzzer is sounding | 10 to 14 V |
| O15-26 (BZR+) - Body ground | B - Body ground | Power back door warning buzzer signal input | Back door warning buzzer is stopped | Below 1 V |
| O15-2 (DC+) - O15-1 (DC-) | B - G | Power back door lock motor circuit | Back door lock motor is operating | 10 to 14 V |
| O15-2 (DC+) - O15-1 (DC-) | B - G | Power back door lock motor circuit | Back door lock motor is stopped | Below 1 V |
| O15-22 (HAF) - Body ground | R - Body ground | Back door lock half-latch switch signal circuit | Back door is opened → Back door closer motor is operating → Back door is closed | Below 1 V → 10 to 14 V → Below 1 V |
| O15-24 (POS) - Body ground | LG - Body ground | Back door lock position switch signal circuit | Back door is opened → Back door closer motor is operating → Back door is closed | Below 1 V → 10 to 14 V → Below 1 V |
| CHECK MAIN BODY ECU |

Disconnect the D7, 1F and 1M connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| D7-2 (PBDS) - Body ground | R - Body ground | Power back door open / close switch signal circuit | Power back door open / close switch ON | Below 1 Ω |
| D7-2 (PBDS) - Body ground | R - Body ground | Power back door open / close switch signal circuit | Power back door open / close switch OFF | 10 kΩ or higher |
| 1F-10 (GND1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| 1M-9 (GND2) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |