Home › SECURITIES › THEFT DETERRENT › THEFT DETERRENT SYSTEM (w/o Smart Key System)

THEFT DETERRENT SYSTEM (w/o Smart Key System) > SYSTEM DESCRIPTION



OUTLINE OF THEFT DETERRENT SYSTEM
  1. The theft deterrent system can be set by locking the doors using the transmitter or key, or by opening and closing the doors (see ACTIVE ARMING MODE or PASSIVE ARMING MODE for details).
  2. The alarm function will be activated when someone attempts to forcibly unlock any of the doors or open any of the doors, engine hood, and back door while the system is in the armed state.
  3. In the alarm sounding state, the system illuminates the interior light and blinks the hazard warning lights, the headlights and taillights. At the same time, the system sounds the vehicle horn(s) and security horn to deter break-in and theft as well as to warn people around the vehicle.
  4. The alarm can be cancelled by unlocking the doors using the transmitter or key.
  5. There are two arming modes for this system: active arming mode and passive arming mode. When the active arming mode has been set, the theft deterrent system will be set after the user locks the doors via the transmitter or key. When the passive arming mode has been set, the theft deterrent system will be set after the key is removed and the driver's door is closed.
  1. Disarmed state:

    1. The alarm function is not operating.
    2. The theft deterrent system is not operating.

  2. Arming preparation state:

    1. The time until the system goes into the armed state.
    2. The theft deterrent system is not operating.

  3. Armed state:

    1. The theft deterrent system is operating.

  4. Alarm sounding state:

    1. The alarm function is operating.

    Alarm time:
    Approx. 60 sec.


    Refer to the table below for alarm methods and time: 
    Alarm Method
    Headlights
    Blinking
    Taillights
    Blinking
    Hazard Warning Lights
    Blinking
    Interior Light
    Illuminating
    Vehicle Horn(s)
    Sounding
    (approx. 0.4 second cycles)
    Security Horn
    Sounding
    Alarm Time
    Approx. 60 sec.

    HINT:
    If any of the doors are unlocked when the key is not in the key cylinder during the armed state, a forced door lock signal will be output (see FORCED DOOR LOCK CONTROL).


FUNCTION OF MAIN COMPONENTS

Component
Function
Security indicator
Informs driver of theft deterrent system status.
Security horn
Sounds when attempted break-in or theft is detected.
Headlights
Blink when attempted break-in or theft is detected.
Taillights
  1. Blink when attempted break-in or theft is detected.
  2. Come on when theft deterrent system has entered into alarm sounding state.
Hazard warning lights
Blink when attempted break-in or theft is detected.
Interior light
Comes on when attempted break-in or theft is detected.
Vehicle horn(s)
Sound when attempted break-in or theft is detected.
Door courtesy light switch
Detects door status (open or closed).
Door unlock detection switch
Detects door status (locked or unlocked).
Engine hood courtesy switch
Detects engine hood status (open or closed).
Back door courtesy switch
Detects back door status (open or closed).
Glass hatch courtesy switch*
Detects glass hatch status (open or closed).

HINT:
*: w/ Glass Hatch Opener System


ACTIVE ARMING MODE

HINT:
Active arming mode starts the alarm control immediately after the doors are locked.



  1. Active arming mode:
    This system operates as described in the diagram below when one of the items for each condition is met.


    B112141E03

    HINT:
    The below terms "all doors" and "door" also refer to the back door.


    Condition
    Item
    Condition (1)
    In the disarmed state, the system state is switched if one of the following conditions is met when the key is not in the key cylinder:
    1. With all doors, engine hood, and glass hatch* closed, all doors are locked by key operation.
    2. With all doors, engine hood, and glass hatch* closed, all doors are locked by wireless operation.
    3. With the engine hood closed, any door or the glass hatch* is closed and all doors are locked without using the key.
    Condition (2)
    Approx. 30 seconds elapse after condition (1) is met.
    Condition (3)
    1. A wireless unlock signal is received.
    2. The driver's door only or all doors are unlocked by key operation.
    3. Any door is unlocked.
    4. Any door or the glass hatch* is opened.
    5. The key is inserted into the ignition key cylinder.
    6. The ignition switch is turned to the ON or ACC position.
    7. The battery is reconnected.
    Condition (4)
    1. The engine hood is opened.
    2. The battery is reconnected.
    3. Any door or the glass hatch* is opened.
    4. Any door is unlocked when all doors are locked.
    5. The ignition switch is turned to the ON position without using the key.
    Condition (5)
    1. A wireless unlock signal is received.
    2. The driver's door only or all doors are unlocked by key operation.
    3. The ignition switch is turned to the ON position and the engine is run for more than 2 seconds.
    Condition (6)
    Approx. 60 seconds elapse. (The alarm stops and the system returns to the armed state.)

    HINT:
    *: w/ Glass Hatch Opener System


PASSIVE ARMING MODE

HINT:
  1. Passive arming mode starts the alarm control after the key is removed from the key cylinder and the doors are closed.
  2. Passive arming mode can be switched ON/OFF using Techstream.
  3. The alarm is initially set (when shipped from the factory) to active arming mode (not passive arming mode).
  4. During passive arming mode, the theft deterrent system goes into the armed state even if the doors are not locked.
  5. Detecting that the doors are unlocked does not set off the alarm during passive arming mode.
  6. A forced door lock signal is not output during passive arming mode (see FORCED DOOR LOCK CONTROL).
  7. Although the theft deterrent system detects that the doors are opened during passive arming mode, the alarm will not go off immediately because an entry delay time is set.
  8. If condition (1) of active arming mode is met during passive arming mode, the theft deterrent system will switch to active arming mode.



  1. Passive arming mode:
    This system operates as described in the diagram below when one of the items for each condition is met.


    B164960E03

    HINT:
    The below terms "all doors" and "door" also refer to the back door.


    Condition
    Item
    Condition (1)
    1. With the ignition switch off, any door or the glass hatch*1 is opened and then the key is removed from the ignition key cylinder.
    2. With the ignition switch off, the key is removed from the ignition key cylinder and then any door or the glass hatch*1 is opened.
    Condition (2)
    1. An open door(s) or the glass hatch*1 is closed with the other door(s), glass hatch*1, and engine hood closed.
    2. The engine hood is closed with all doors and the glass hatch*1 closed.
    Condition (3)
    1. A wireless unlock signal is received.
    2. The driver's door only or all doors are unlocked by key operation.
    3. The battery is reconnected.
    4. The key is inserted into the ignition key cylinder.
    5. The ignition switch is turned to the ON or ACC position.
    Condition (4)
    Approx. 30 seconds elapse after condition (1) is met.
    Condition (5)
    1. Any door or the glass hatch*1 is opened.
    2. The engine hood is opened.
    Condition (6)
    1. Any door or the glass hatch*1 is opened and the entry delay time*2 elapse.
    2. The engine hood is opened.
    3. The battery is reconnected.
    4. The ignition switch is turned to the ON position without using the key.
    Condition (7)
    1. A wireless unlock signal is received.
    2. The driver's door only or all doors are unlocked by key operation.
    3. The ignition switch is turned to the ON position and the engine is run for more than 2 seconds.
    4. The ignition switch is turned to the ON position without using the key.
    Condition (8)
    Approx. 60 seconds elapse. (The alarm stops and the system returns to the armed state.)

    HINT:
    1. *1: w/ Glass Hatch Opener System
    2. *2: When any door is opened while all the doors are closed during passive arming mode, the entry delay time starts. If the switch condition (armed state → disarmed state (1) or (2)) is met during the entry delay time, the theft deterrent system will return to disarmed state (1) or (2). However, if the switch condition for disarmed state (1) or (2) is not met, the theft deterrent system will recognize it as a theft and set off the alarm. Entry delay time of 0, 14 or 30 sec. can be selected by the customizing function.


FORCED DOOR LOCK CONTROL
  1. The forced door lock control prevents the vehicle from being tampered with. Immediately after a door is unlocked (alarm starts), all doors are forced to lock by a forced door lock signal.

    1. Conditions that force the doors to lock:
      The key is not in the key cylinder and both of the following conditions are met:

      1. The theft deterrent system is in the alarm sounding state of active arming mode.
      2. Any door is unlocked.


ALARM MEMORY FUNCTION
  1. If the alarm is set off (tampering is detected) while the theft deterrent system is armed, it will be recorded by the alarm memory function. Whenever the theft deterrent system is cancelled, the alarm memory function causes the taillights to light up for 2 seconds in order to inform you that the alarm has been set off.

    1. Conditions that cause the taillights to light up for 2 seconds:
      The theft deterrent system has entered the alarm sounding state (tampering has been detected) even once and either of the following conditions is met:

      1. Switched to the disarmed state from the armed state during active arming mode.
      2. Switched to the disarmed state 1 from the armed state during passive arming mode.

      HINT:
      Active arming mode: See ACTIVE ARMING MODE.
      Passive arming mode: See PASSIVE ARMING MODE.


PANIC ALARM CONTROL
  1. The panic alarm control makes it possible to voluntarily set off the panic alarm by pressing the PANIC switch on the wireless transmitter.

    1. Conditions that cause the panic alarm control to set off the panic alarm:
      The PANIC switch on the wireless transmitter is pressed under the following conditions:

      1. The ignition switch is off.
      2. The theft deterrent system is not in the alarm sounding state. (This condition is common to both active arming mode and passive arming mode.)

    2. Conditions that cause the panic alarm control to shut off the alarm:
      Any of the following conditions is met during panic alarm operation:

      1. The ignition switch is turned to the ON position.
      2. The PANIC switch is pressed again.
      3. Any of the switches on the wireless transmitter (LOCK/UNLOCK/POWER BACK DOOR*1 or GLASS HATCH OPEN*2) is pressed.
      4. The panic alarm ends (approx. 60 sec. have passed).
      5. The theft deterrent system switches to the alarm sounding state. Under this condition, the theft deterrent system is controlling the alarm rather than the panic alarm control. In order to cancel this alarm, refer to the theft deterrent system alarm sounding state cancellation procedure. (This condition is common to both active arming mode and passive arming mode.)

      HINT:
      1. *1: w/ Power Back Door System
      2. *2: w/ Glass Hatch Opener System
      3. Active arming mode: See ACTIVE ARMING MODE.
      4. Passive arming mode: See PASSIVE ARMING MODE.


SECURITY INDICATOR OUTPUT
  1. The main body ECU outputs a signal to come on the security indicator, according to the state of the theft deterrent system. However, some of the actual lighting conditions of the security indicator are different from the output signals of the main body ECU.

    Output: 
    State of Theft Deterrent System
    Security Indicator
    Output Signal from Main Body ECU
    Actual Lighting Condition
    Disarmed state (1), (2)
    OFF
    OFF (Immobiliser system unset)
    BLINKING (Immobiliser system set)
    Arming preparation state
    ON
    ON
    Armed state
    OFF
    BLINKING
    Alarm sounding state
    ON
    ON
    Blinking cycle: 
    Time
    Security Indicator
    0.2 sec.
    ON
    1.8 sec.
    OFF

    HINT:
    When the immobiliser system is set, the security indicator blinks during both the disarmed state and the armed state, due to output signals from the immobiliser system.