AIR OUTLET CONTROL SERVO MOTOR (for Rear) > INSTALLATION |
| 1. INSTALL REAR AIR OUTLET CONTROL SERVO MOTOR SUB-ASSEMBLY |
![]() |
Using the reference point, install the rear air outlet control servo motor sub-assembly with the 2 screws.
Connect the connector.
| 2. INSTALL REAR COOLING UNIT ASSEMBLY |
![]() |
Install the rear cooling unit assembly with the 4 bolts.
![]() |
Connect each connector.
Engage each clamp.
| 3. INSTALL REAR NO. 5 AIR DUCT |
![]() |
Install the rear No. 5 air duct with the 2 clips.
| 4. INSTALL NO. 1 COOLER AIR DUCT |
![]() |
Install the No. 1 cooler air duct as shown in the illustration.
| 5. INSTALL COOLER PLATE |
![]() |
Engage the 2 claws and install the cooler plate.
| 6. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH |
| 7. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH |
Engage the 4 clips and the 7 claws.
Install the 2 clips.
Install the deck trim side panel assembly RH with the 3 bolts.

| 8. INSTALL FRONT DECK SIDE TRIM COVER RH |
| 9. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK |
| 10. INSTALL ROPE HOOK ASSEMBLY (for RH Side) |
| 11. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH |
![]() |
Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.
| 12. INSTALL SIDE TRIM COVER RH (for Manual Air Conditioning System) |
![]() |
Engage the 4 claws, and install the side trim cover RH.
| 13. INSTALL REAR ROOM TEMPERATURE SENSOR (for Automatic Air Conditioning System) |
Connect the connector.
![]() |
Engage the 4 claws and install the rear room temperature sensor.
| 14. INSTALL DECK SIDE TRIM RH |
| 15. INSTALL DECK SIDE TRIM COVER RH |
| 16. INSTALL REAR SEAT SIDE GARNISH CAP |
![]() |
Engage the guide and the 6 claws.
Install the rear seat side garnish cap with the screw.
| 17. INSTALL REAR FLOOR FINISH PLATE |
![]() |
Engage the 4 clips and the 4 claws, and install the rear floor finish plate.
| 18. INSTALL REAR NO. 2 SEAT ASSEMBLY |
![]() |
Install the rear No. 2 seat assembly with the 4 bolts.
| 19. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH |
![]() |
Install the rear seat lap type belt assembly LH with the bolt.
| 20. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH |
Install the rear seat lap type belt assembly RH with the bolt.
| 21. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY |
![]() |
Install the rear No. 2 seat inner belt assembly with the bolt.
| 22. INSTALL REAR MAT |
![]() |
Install the rear mat.
| 23. INSTALL DECK FLOOR BOARD ASSEMBLY |
![]() |
Install the 2 nuts and the deck floor board assembly.
Engage the 3 claws.
| 24. INSTALL DECK SIDE TRIM BOX LH |
Install the deck side trim box LH as shown in the illustration.

![]() |
Install the 2 deck side trim clip and the clips.
| 25. INSTALL REAR SEAT SIDE COVER LH |
![]() |
Engage the 2 clips and install the rear seat side cover LH.
| 26. INSTALL DECK SIDE TRIM BOX RH |
Install the deck side trim box RH as shown in the illustration.

![]() |
Install the 2 deck side trim clip and the clip.
| 27. INSTALL JACK CARRIER ASSEMBLY |
![]() |
Engage the 3 claws, and install the jack carrier assembly.
| 28. INSTALL JACK ASSEMBLY |
![]() |
Install the jack assembly.
| 29. INSTALL JACK CARRIER CUSHION |
![]() |
Install the jack carrier cushion.
| 30. INSTALL JACK CARRIER SUPPORT |
| 31. INSTALL REAR SEAT SIDE COVER RH |
![]() |
Engage the 2 clips and install the rear seat side cover RH.
| 32. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Install the tonneau cover assembly.
| 33. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY |
![]() |
Engage the 2 guides and install the No. 2 deck board sub-assembly.
| 34. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY |
![]() |
Engage the 2 guides and install the No. 3 deck board sub-assembly.
| 35. INSTALL DECK BOARD ASSEMBLY |
![]() |
Install the deck board sub-assembly.
| 36. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
| 37. INSTALL REAR DOOR SCUFF PLATE RH |
| 38. CONNECT COOLER REFRIGERANT LIQUID PIPE C |
Remove the attached vinyl tape from the tube.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant liquid pipe C.
Install the O-ring on the cooler refrigerant liquid pipe C.
Install the cooler refrigerant liquid pipe C.
| 39. CONNECT COOLER REFRIGERANT SUCTION HOSE |
Remove the attached vinyl tape from the hose.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant suction hose.
Install the O-ring on the cooler refrigerant suction hose.
Move the hook connector in the direction indicated by the arrow in the illustration.
![]() |
Insert the pipe joint into the fitting hole securely and tighten the bolt.
| 40. CONNECT REAR HEATER INLET WATER HOSE |
![]() |
Install the water hose and attach the clip.
| 41. CONNECT REAR HEATER OUTLET WATER HOSE |
![]() |
Install the water hose and attach the clip.
| 42. CHARGE WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump.
Charge with refrigerant HFC-134a (R134a).

| 43. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the 2 cylinder block drain cock plugs.
Loosen the air drain cock plug from the water inlet housing.
![]() |
Loosen the air drain plug at the top of the radiator 3 or 4 turns.
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.
Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
| Condition | Specified Condition |
| w/ Rear Heater | 11.0 liters (11.6 US qts, 9.7 Imp. qts) |
| w/o Rear Heater | 8.8 liters (9.3 US qts, 7.7 Imp. qts) |
| Condition | Specified Condition |
| w/ Rear Heater | 11.7 liters (12.4 US qts, 10.3 Imp. qts) |
| w/o Rear Heater | 9.5 liters (10.1 US qts, 8.4 Imp. qts) |
Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the FULL line on the radiator reservoir.
| 44. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 45. WARM UP ENGINE |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 46. INSPECT FOR REFRIGERANT LEAK |
After recharging with refrigerant gas, inspect for refrigerant leak using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a gas leak detector, inspect for refrigerant leak from the refrigerant lines.
![]() |
Bring the gas leak detector close to the drain hose with the detector's power off, and then turn the detector on.
If a gas leak is not detected from the drain hose, remove the blower motor from the cooling unit. Insert the gas leak detector into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.