Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1447/47    Rear Air Mix Damper Control Servo Motor Circuit

for Preparation Click here


DESCRIPTION

The rear air mix control servo motor sends pulse signals to indicate the damper position to the air conditioning amplifier. The air conditioning amplifier activates the motor (normal or reverse) based on these signals to move the rear air mix damper to the appropriate position. This adjusts the amount of air passing through the heater core after passing the evaporator and controls the temperature of the blown air.

HINT:
Confirm that there are no mechanical problems because this DTC can be set if either a damper link or damper is mechanically locked.


DTC No.
DTC Detection Condition
Trouble Area
B1447/47
Rear air mix damper position does not change even if air conditioning amplifier operates rear air mix control servo motor
  1. Rear air mix control servo motor
  2. Rear air conditioning harness
  3. Wire harness between rear air conditioning harness and air conditioning amplifier
  4. Air conditioning amplifier

WIRING DIAGRAM


E127600E21


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG) and turn Techstream main switch on.

  1. Select the item below in the Data List, and read the value displayed on Techstream.

    Data List / Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Mix Servo Targ Pulse(R)
    Rear air mix control servo motor target pulse /
    Min.: 0, Max.: 255
    MAX. COLD: 9 (pulse)
    MAX. HOT: 54 (pulse)
    -

    OK:
    The display is as specified in the normal condition column.


    Result:

    Result
    Proceed to
    NG
    A
    OK (Checking from PROBLEM SYMPTOMS TABLE)
    B
    OK (Checking from DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
A


2.CHECK HARNESS AND CONNECTOR (REAR AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)


    E153085E06
  1. Disconnect the N12 rear air conditioning harness connector.

  1. Disconnect the D38 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N12-2 (RBUG) - D38-21 (RBUG)
    Always
    Below 1 Ω
    N12-3 (RBUS) - D38-1 (RBUS)
    Always
    Below 1 Ω
    N12-4 (RBBU) - D38-23 (RBBU)
    Always
    Below 1 Ω
    D38-21 (RBUG) - Body ground
    Always
    10 kΩ or higher
    D38-1 (RBUS) - Body ground
    Always
    10 kΩ or higher
    D38-23 (RBBU) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE REAR AIR MIX CONTROL SERVO MOTOR
  1. Replace the rear air mix control servo motor (Click here).


NEXT


4.CHECK DTC OUTPUT
  1. Clear the DTC (Click here).

  1. Check for DTC (Click here).

    OK:
    DTC B1447/47 is not output.



NG
REPAIR OR REPLACE REAR AIR CONDITIONING HARNESS
OK

END (REAR AIR MIX CONTROL SERVO MOTOR IS DEFECTIVE)