Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > Rear Blower Motor Circuit

for Preparation Click here


DESCRIPTION

The rear blower motor is operated by signals from the air conditioning amplifier. Rear blower motor speed signals are transmitted in accordance with changes in the duty ratio.

E115031E07


WIRING DIAGRAM


E127601E06


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG) and turn Techstream main switch on.

  1. Select the item below in the Active Test, and then check that the rear blower motor operates.

    Active Test / Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Blower Motor
    Rear blower motor
    Min.: 0, Max.: 31
    -

    Result:

    Result
    Proceed to
    NG (blower motor does not operate)
    A
    NG (blower motor operates but does not change speed)
    B
    OK
    C



B
Go to step 6

C
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A


2.INSPECT FUSE (RR CLR)
  1. Remove the RR CLR H-fuse from the main body ECU.

  1. Measure the resistance of the H-fuse.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    RR CLR H-fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3.INSPECT REAR BLOWER MOTOR


    E153715E01
  1. Disconnect the N10 motor connector.

  1. Connect the battery's positive (+) lead to terminal 2 and the negative (-) to terminal 1, then check that the rear blower motor operates smoothly.

    OK:
    The rear blower motor operates smoothly.

  1. Measure the current of the connector.

    Standard current:
    Tester Connection
    Condition
    Specified Condition
    N10-1 - N10-2
    Rear blower motor operates
    Below 13.5 A



NG
REPLACE REAR BLOWER MOTOR
OK


4.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR CONTROL - BODY GROUND)


    E153716E01
  1. Disconnect the N11 rear motor control connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N11-6 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR CONTROL - BATTERY)


    E153716E03
  1. Disconnect the N11 rear motor control connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    N11-1 (+B) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BODY GROUND)


    E153680E02
  1. Disconnect the D38 amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D38-22 (BLWH) - D38-20 (GND2)
    Ignition switch on (IG)
    Blower switch OFF
    4.5 to 5.5 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK AIR CONDITIONING AMPLIFIER


    E127604E03
  1. Remove the air conditioning amplifier with its connectors still connected.

  1. Check the waveform of the amplifier connector.

    OK:
    Waveform is as shown in the illustration.

    HINT:
    The waveform varies with the blower level.

    Item
    Content
    Tester Connection
    BLWH (D38-22) - GND2 (D38-20)
    Tool Setting
    1 V/DIV., 500 μsec./DIV.
    Condition
    Ignition switch on (IG)
    Blower switch LO



NG
REPLACE AIR CONDITIONING AMPLIFIER
OK

REPLACE REAR BLOWER MOTOR