Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

DTC    U1002 (CAN MS BUS)    Lost Communication with Gateway Module (Main body ECU)

for Preparation Click here


DESCRIPTION

  1. The main body ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to the CAN MS bus.
  2. When the main body ECU receives a response signal from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECU is connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.

DTC No.
DTC Detection Condition
Trouble Area
U1002
Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to the CAN MS bus.
  1. Open or short in CAN MS bus main wire or connector
  2. Open or short in CAN MS bus branch wire or connector
  3. Main body ECU
  4. Certification ECU
  5. Back door ECU
  6. CAN junction connector RR

WIRING DIAGRAM


C169780E03


C169781E03


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.

1.CHECK VEHICLE TYPE

Result:
Result
Proceed to
w/o Power back door
A
w/ Power back door
B



B
Go to step 6
A


2.CHECK CAN MS BUS WIRE
  1. Turn the ignition switch off.

  1. Disconnect the certification ECU connector.



    C152870E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Result
    D40-27 (CANH) - D40-28 (CANL)
    Ignition switch off
    108 to 132 Ω
    Below 107 Ω: Short in line
    133 Ω or more: Open in CAN main bus line
    D40-27 (CANH) - D40-17 (E)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    D40-28 (CANL) - D40-17 (E)
    D40-27 (CANH) - D40-1 (+B)
    Negative battery terminal disconnected
    6 kΩ or higher
    Below 6 kΩ: +B short
    D40-28 (CANL) - D40-1 (BAT)

    Result:
    Result
    Proceed to
    OK
    A
    Open in CAN main wire
    B
    Short in line, Ground short, +B short
    C



B
Go to step 4

C
Go to step 5
A


3.CHECK CAN MS BUS WIRE
  1. Reconnect the certification ECU connector.

  1. Disconnect the main body ECU connector.



    C195603E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D9-16 (CANP) - D9-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    D9-16 (CANP) - D47-4 (CG)
    Ignition switch off
    200 Ω or higher
    D9-15 (CANN) - D47-4 (CG)
    D9-16 (CANP) - D47-16 (BAT)
    Negative battery terminal disconnected
    6 kΩ or higher
    D9-15 (CANN) - D47-16 (BAT)



NG
REPLACE CERTIFICATION ECU
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (MAIN BODY ECU) 

4.CHECK FOR OPEN IN CAN MS BUS MAIN WIRE
  1. Reconnect the certification ECU connector.

  1. Disconnect the main body ECU connector.



    C195604E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D9-16 (CANP) - D9-15 (CANN)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU - CERTIFICATION ECU)
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (MAIN BODY ECU) 

5.CHECK FOR SHORT IN CAN MS BUS WIRES
  1. Disconnect the main body ECU connector (D9).



    C195603E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D9-16 (CANP) - D9-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    D9-16 (CANP) - D47-4 (CG)
    Ignition switch off
    200 Ω or higher
    D9-15 (CANN) - D47-4 (CG)
    D9-16 (CANP) - D47-16 (BAT)
    Negative battery terminal disconnected
    6 kΩ or higher
    D9-15 (CANN) - D47-16 (BAT)



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU - CERTIFICATION ECU)
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (MAIN BODY ECU) 

6.CHECK CAN MS BUS WIRE
  1. Turn the ignition switch off.



    C170105E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Result
    O15-6 (MPX1) - O15-5 (MPX2)
    Ignition switch off
    54 to 69 Ω
    Below 54 Ω: Short in line
    70 Ω or more: Open in CAN main bus line
    O15-6 (MPX1) - O15-11 (GND)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    O15-5 (MPX2) - O15-11 (GND)
    O15-6 (MPX1) - O15-12 (B)
    Negative battery terminal disconnected
    6 kΩ or higher
    Below 6 kΩ: +B short
    O15-5 (MPX2) - O15-12 (B)

    Result:
    Result
    Proceed to
    OK
    A
    Open in CAN main wire
    B
    Short in line, Ground short, +B short
    C



B
Go to step 7

C
Go to step 10
A

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (MAIN BODY ECU) 

7.CHECK FOR OPEN IN CAN MS BUS MAIN WIRE


    C165804E08
  1. Disconnect the main body ECU junction connector from the CAN junction connector RR.



    C169769E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O15-6 (MPX1) - O15-5 (MPX2)
    Ignition switch off
    108 to 132 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (w/o Smart key system)
    B
    NG (w/ Smart key system)
    C



B
REPLACE CAN JUNCTION CONNECTOR RR

C
Go to step 9
A


8.CHECK FOR OPEN IN CAN MS BUS MAIN WIRE
  1. Reconnect the main body ECU junction connector to the CAN junction connector RR.

  1. Disconnect the main body ECU connector (D9) from the main body ECU.



    C195604E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D9-16 (CANP) - D9-15 (CANN)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU MAIN WIRE)
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (MAIN BODY ECU) 

9.CHECK FOR OPEN IN CAN MS BUS MAIN WIRE
  1. Reconnect the main body ECU junction connector to the CAN junction connector RR.

  1. Disconnect the certification ECU connector from the certification ECU.



    C152870E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D40-27 (CANH) - D40-28 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CERTIFICATION ECU BRANCH WIRE)
OK

REPLACE CERTIFICATION ECU 

10.CHECK FOR SHORT IN CAN MS BUS WIRES
  1. Disconnect the back door ECU connector.



    C169769E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O15-6 (MPX1) - O15-5 (MPX2)
    Ignition switch off
    54 to 69 Ω
    O15-6 (MPX1) - O15-11 (GND)
    Ignition switch off
    200 Ω or higher
    O15-5 (MPX2) - O15-11 (GND)
    O15-6 (MPX1) - O15-12 (B)
    Negative battery terminal disconnected
    6 kΩ or higher
    O15-5 (MPX2) - O15-12 (B)



NG
Go to step 11
OK

REPLACE BACK DOOR MOTOR UNIT (BACK DOOR ECU) (Click here)  

11.CHECK FOR SHORT IN CAN MS BUS WIRES


    C165804E09
  1. Disconnect the back door ECU junction connector from the CAN junction connector RR.



    C169769E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O15-6 (MPX1) - O15-5 (MPX2)
    Ignition switch off
    1 MΩ or higher
    O15-6 (MPX1) - O15-11 (GND)
    Ignition switch off
    200 Ω or higher
    O15-5 (MPX2) - O15-11 (GND)
    O15-6 (MPX1) - O15-12 (B)
    Negative battery terminal disconnected
    6 kΩ or higher
    O15-5 (MPX2) - O15-12 (B)



NG
REPAIR OR REPLACE CAN MS BUS BRANCH WIRE OR CONNECTOR (BACK DOOR ECU)
OK


12.CHECK FOR SHORT IN CAN MS BUS WIRES
  1. Reconnect the back door ECU junction connector to the CAN junction connector RR.



    C165804E08
  1. Disconnect the main body ECU junction connector from the CAN junction connector RR.



    C169769E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O15-6 (MPX1) - O15-5 (MPX2)
    Ignition switch off
    108 to 132 Ω
    O15-6 (MPX1) - O15-11 (GND)
    Ignition switch off
    200 Ω or higher
    O15-5 (MPX2) - O15-11 (GND)
    O15-6 (MPX1) - O15-12 (B)
    Negative battery terminal disconnected
    6 kΩ or higher
    O15-5 (MPX2) - O15-12 (B)

    Result:
    Result
    Proceed to
    OK
    A
    NG (w/o Smart key system)
    B
    NG (w/ Smart key system)
    C



B
REPLACE CAN JUNCTION CONNECTOR RR

C
Go to step 14
A


13.CHECK FOR SHORT IN CAN BUS MAIN WIRE
  1. Reconnect the main body ECU junction connector to the CAN junction connector RR.

  1. Disconnect the main body ECU connector (D9) from the main body ECU.



    C195603E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D9-16 (CANP) - D9-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    D9-16 (CANP) - D47-4 (CG)
    Ignition switch off
    200 Ω or higher
    D9-15 (CANN) - D47-4 (CG)
    D9-16 (CANP) - D47-16 (BAT)
    Negative battery terminal disconnected
    6 kΩ or higher
    D9-15 (CANN) - D47-16 (+B)



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU MAIN WIRE)
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (MAIN BODY ECU) 

14.CHECK FOR SHORT IN CAN MS BUS WIRES
  1. Reconnect the main body ECU junction connector to the CAN junction connector RR.



    C165804E10
  1. Disconnect the certification ECU junction connector from the CAN junction connector RR.



    C169769E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O15-6 (MPX1) - O15-5 (MPX2)
    Ignition switch off
    108 to 132 Ω
    O15-6 (MPX1) - O15-11 (GND)
    Ignition switch off
    200 Ω or higher
    O15-5 (MPX2) - O15-11 (GND)
    O15-6 (MPX1) - O15-12 (B)
    Negative battery terminal disconnected
    6 kΩ or higher
    O15-5 (MPX2) - O15-12 (B)



NG
REPLACE CAN JUNCTION CONNECTOR RR
OK


15.CHECK FOR SHORT IN CAN MS BUS WIRES
  1. Reconnect the certification ECU junction connector to the CAN junction connector RR.

  1. Disconnect the certification ECU connector from the certification ECU.



    C152870E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D40-27 (CANH) - D40-28 (CANL)
    Ignition switch off
    108 to 132 Ω
    D40-27 (CANH) - D40-17 (E)
    Ignition switch off
    200 Ω or higher
    D40-28 (CANL) - D40-17 (E)
    D40-27 (CANH) - D40-1 (+B)
    Negative battery terminal disconnected
    6 kΩ or higher
    D40-28 (CANL) - D40-1 (+B)



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CERTIFICATION ECU BRANCH WIRE)
OK

REPLACE CERTIFICATION ECU