Home › BRAKE › BRAKE › BRAKE PEDAL

BRAKE PEDAL > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY


    C165374
  1. Install the brake pedal support sub-assembly with the 4 nuts.

    Torque:
    13 N*m{ 132 kgf*cm , 10 ft.*lbf }



    C165373
  1. Install the brake pedal support sub-assembly to the instrument panel reinforcement with the 2 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



    C165371
  1. Connect the brake pedal load sensing switch connector and engage the clamp.



2. CONNECT BRAKE MASTER CYLINDER PUSH ROD CLEVIS


    C170591E01
  1. Apply lithium soap base glycol grease to the push rod pin.

  1. Connect the brake master cylinder push rod clevis to the brake pedal with the push rod pin, and install a new clip as shown in the illustration.



3. INSTALL BRAKE PEDAL RETURN SPRING


    C165369
  1. Install the brake pedal return spring between the instrument panel reinforcement and brake master cylinder push rod clevis.



4. INSTALL STOP LIGHT SWITCH ASSEMBLY


    E150075E01
  1. Temporarily install the stop light switch assembly with the stop light switch lock nut.



    E150611E01
  1. Turn the stop light switch assembly so that the clearance between the nut end and stop light switch cushion is between 0.5 to 2.4 mm (0.020 to 0.095 in.).

  1. Tighten the stop light switch lock nut.

    Torque:
    17 N*m{ 173 kgf*cm , 12 ft.*lbf }



    E150073
  1. Connect the connector.



5. INSPECT AND ADJUST BRAKE PEDAL HEIGHT


  1. Check the brake pedal height.



      C165370E01
    1. Turn back the carpet.

    2. Measure the shortest distance between the brake pedal surface and tibia pad.

      Pedal height from tibia pad:
      148.8 to 158.8 mm (5.858 to 6.252 in.)

  1. Adjust the brake pedal height.

    1. Disconnect the stop light switch connector.

    2. Remove the stop light switch assembly.

    3. Loosen the push rod clevis lock nut.

    4. Adjust the brake pedal height by turning the push rod.

    5. Tighten the push rod clevis lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    6. Install and adjust the stop light switch .

      NOTICE:
      Do not depress the brake pedal.

    7. Connect the stop light switch connector.



6. INSPECT BRAKE PEDAL FREE PLAY


    C132708E01
  1. Stop the engine. Depress the pedal several times until no vacuum is left in the brake booster. Release the brake pedal.

  1. Depress the pedal until a slight resistance is felt. Measure the distance as shown in the illustration.

    Pedal free play:
    1.0 to 6.0 mm (0.039 to 0.236 in.)

    If the pedal free play is not as specified, check the stop light switch clearance . If the pedal free play is as specified, proceed to the "INSPECT BRAKE PEDAL RESERVE DISTANCE" procedure.



7. INSPECT BRAKE PEDAL RESERVE DISTANCE

HINT:
Measure the distance at the same point used for the brake pedal height inspection.



    C111339E05
  1. Release the parking brake lever.

  1. With the engine running, depress the brake pedal and measure the pedal reserve distance as shown in the illustration.

    Pedal reserve distance from the tibia pad at 500 N (51 kgf, 112 lbf):
    84.4 mm (3.32 in.)

    If the distance is not as specified, troubleshoot the brake system (Click here).



8. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)


    B168371
  1. Connect the hood lock control cable assembly.

  1. Connect each connector.

  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.



9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)


    B173009
  1. Connect the hood lock control cable assembly.

  1. Connect each connector and the aspirator duct.



    B173021
  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.



10. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    B173227
  1. Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.



11. INSTALL FRONT DOOR SCUFF PLATE LH


    B173224
  1. Engage the guide and the 8 claws, and install the front door scuff plate LH.