BRAKE MASTER CYLINDER > INSTALLATION |
| 1. INSPECT AND ADJUST BRAKE BOOSTER PUSH ROD |
Apply chalk to the tip of the accessory tool.
![]() |
Place the accessory tool on the brake booster assembly.
Measure the clearance between the brake booster push rod and accessory tool.
![]() |
If the clearance is not as specified, adjust the push rod length by holding the rod using SST and turning the tip of the rod using a socket driver (7 mm).
| 2. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY |
Install a new O-ring to the brake master cylinder sub-assembly.
![]() |
Install the brake master cylinder sub-assembly to the brake booster assembly with the 2 nuts.
| 3. CONNECT BRAKE LINE |
![]() |
Using a union nut wrench (12 mm), connect the 2 brake lines to the brake master cylinder sub-assembly.
| 4. CONNECT NO. 1 RESERVOIR TUBE |
Connect the No. 1 reservoir tube to the brake master cylinder reservoir assembly.
| 5. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY |
![]() |
Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.
![]() |
Engage the 4 clamps.
| 6. INSTALL WINDSHIELD WIPER MOTOR AND LINK |
![]() |
Install the windshield wiper motor and link assembly with the 4 bolts.
Connect the connector.
| 7. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
Engage the 20 claws.

Install the cowl top ventilator louver sub-assembly with the 2 clips.
![]() |
Engage the 2 claws and connect the front fender to cowl side seal LH.
![]() |
Engage the 2 claws and connect the front fender to cowl side seal RH.
| 8. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
When reinstalling:
![]() |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 25.6 mm (1.00 in.) |
| 9. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
When reinstalling:
![]() |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 31.9 mm (1.26 in.) |
Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.
| 10. FILL BRAKE FLUID RESERVOIR |
![]() |
Fill the reservoir with brake fluid.
| 11. BLEED BRAKE MASTER CYLINDER |
![]() |
Using a union nut wrench (12 mm), disconnect the 2 brake lines from the master cylinder.
![]() |
Slowly depress the brake pedal and hold it (*1).
![]() |
Cover the 2 outer holes with fingers, and release the brake pedal (*2).
Repeat (*1) and (*2) 3 or 4 times.
![]() |
Using a union nut wrench (12 mm), connect the 2 brake lines to the master cylinder.
| 12. BLEED BRAKE LINE |
![]() |
Connect a vinyl tube to the bleeder plug.
Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed (*3).
![]() |
When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (*4).
Repeat (*3) and (*4) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedure for each wheel to bleed the brake line.
| 13. BLEED BRAKE ACTUATOR |
Depress the brake pedal more than 20 times with the ignition switch off.
Connect Techstream to the DLC3, and then turn the ignition switch on (IG).
Turn Techstream on and select "AIR BLEEDING" on the screen.
Bleed the air according to "Step 1: Increase Line" on the Techstream display.
![]() |
Connect a vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*5).
![]() |
When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (*6).
Repeat (*5) and (*6) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedure for the rest of the wheels to bleed the brake lines.
Bleed the suction line according to "Step 2: Inhalation Line" on the Techstream display.
![]() |
Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.
Operate the brake actuator assembly to bleed the air using Techstream (*7).
![]() |
Check that the actuator operation has stopped by referring to the Techstream display, and tighten the bleeder plug (*8).
Repeat (*7) and (*8) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
For the rest of the wheels, bleed the air in the same way as stated in the above procedure.
Bleed the pressure reduction line according to "Step 3: Decrease Line" on the Techstream display.
![]() |
Connect a vinyl tube to either one of the bleeder plugs.
Loosen the bleeder plug (*9).
While keeping the brake pedal fully depressed, operate the brake actuator assembly using Techstream.
![]() |
Tighten the bleeder plug, and then release the brake pedal (*10).
Repeat steps (*9) to (*10) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedures for the rest of the brakes to bleed the brake lines.
Bleed the brake lines again according to "Step 4: Increase Line" on the Techstream display.
![]() |
Connect a vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*11).
![]() |
When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (*12).
Repeat (*11) and (*12) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedures for each brake to bleed the brake lines.
Finish "AIR BLEEDING" on Techstream, and then turn off Techstream.
Disconnect Techstream from the DLC3.
Turn the ignition switch off.
| 14. INSPECT FOR BRAKE FLUID LEAK |
| 15. INSPECT FLUID LEVEL |
![]() |
Check the fluid level.
If brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.