Home › BRAKE › BRAKE › BRAKE BOOSTER

BRAKE BOOSTER > REMOVAL

for Preparation Click here


NOTICE:
Release the vacuum from the booster by depressing the brake pedal several times. Then remove the brake master cylinder sub-assembly from the brake booster assembly.



1. REMOVE V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.



2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E150144
  1. Remove the nut, and the front wiper arm and blade assembly LH.



3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E150145
  1. Remove the nut, and the front wiper arm and blade assembly RH.



4. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E150146
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal LH.



    E150147
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal RH.



  1. Remove the 2 clips.


    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.



5. REMOVE WINDSHIELD WIPER MOTOR AND LINK


    E150150
  1. Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.



6. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    C165925
  1. Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.



    C165926
  1. Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.



7. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A170887
  1. Disconnect the 3 vacuum hoses.



    A170447
  1. Loosen the No. 1 air cleaner hose clamp.

  1. Disconnect the hose clamps and No. 2 ventilation hose.

  1. Disconnect the mass air flow meter connector.



    A170451
  1. Release the 2 clips, and remove the 2 bolts.

  1. Remove the air cleaner cap sub-assembly and air cleaner filter element.



8. DRAIN BRAKE FLUID


9. DISCONNECT NO. 1 RESERVOIR TUBE
  1. Slide the clip and disconnect the No. 1 reservoir tube from the brake master reservoir assembly.



10. DISCONNECT BRAKE LINE


    C165942
  1. Using a union nut wrench (12 mm), disconnect the 2 brake lines from the brake master cylinder sub-assembly.



11. REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY


    C165944
  1. Remove the 2 nuts and brake master cylinder sub-assembly.

  1. Remove the O-ring from the brake master cylinder sub-assembly.

    NOTICE:
    1. The master cylinder requires careful handling. Do not allow the master cylinder to receive any impact, such as from being dropped. Do not reuse a master cylinder that has been dropped.
    2. Do not strike or pinch the master cylinder piston, and do not cause any damage to the master cylinder piston by any other means.
    3. When installing the master cylinder to the brake booster, or when removing the master cylinder from the brake booster, make sure that the master cylinder is kept horizontal or its tip faces downward (the piston faces upward) to prevent the master cylinder piston from falling out.
    4. Do not allow any foreign objects to contaminate the master cylinder piston. If a foreign object gets on the piston, remove it by using a shop rag or a piece of cloth and then apply an even layer of lithium soap base glycol grease around the circumference (sliding part) of the piston.
    5. Do not use any other type of grease or fluid.



12. DISCONNECT VACUUM HOSE
  1. Slide the clip and disconnect the vacuum hose.



13. REMOVE BRAKE VACUUM CHECK VALVE ASSEMBLY
  1. Remove the vacuum check valve assembly from the brake booster assembly.



14. REMOVE CHECK VALVE GROMMET
  1. Remove the check valve grommet from the brake booster assembly.



15. REMOVE BRAKE PEDAL RETURN SPRING


    C165369
  1. Remove the brake pedal return spring from the push rod pin and instrument panel reinforcement.



16. SEPARATE BRAKE MASTER CYLINDER PUSH ROD CLEVIS
  1. Remove the clip and push rod pin, and separate the brake master cylinder push rod clevis from the brake pedal sub-assembly.



17. REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS


    C165374
  1. Remove the 4 nuts and push out the brake booster assembly.

    NOTICE:
    Do not damage the brake lines.



    C167069E01
  1. Loosen the lock nut, and remove the brake master cylinder push rod clevis and lock nut from the brake booster assembly.



18. SEPARATE ENGINE WIRE


    C165952
  1. Disengage the 9 clamps.

  1. Remove the bolt and separate the engine wire from the body.



19. SEPARATE ENGINE WIRE (w/ Security Horn)


    C165953
  1. Disengage the 9 clamps, and disconnect the alarm horn connector.

  1. Remove the bolt and separate the engine wire from the body.



20. REMOVE BRAKE BOOSTER ASSEMBLY


    C166424
  1. Disengage the 2 clamps and separate the 2 brake lines from the body.

    NOTICE:
    Be careful not to damage the brake lines or clamps. If any parts are damaged, replace them with new ones.

  1. Remove the brake booster assembly from the body.

    NOTICE:
    Do not damage the brake lines.



21. REMOVE BRAKE BOOSTER GASKET
  1. Remove the brake booster gasket from the brake booster assembly.