Home › COMMUNICATION SYSTEM › MULTIPLEX COMMUNICATION › LIN COMMUNICATION SYSTEM

LIN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


  1. Disconnect the D7, D8, 1D and 1F instrument panel junction block assembly connectors.


    B150879E05

  2. Measure the voltage and resistance between the wire harness side connectors and body ground.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1D-10 (BECU)*1 - Body ground
    W - Body ground
    Battery power supply
    Always
    11 to 14 V
    D8-6 (AM1)*2 - Body ground
    GR - Body ground
    Battery power supply
    Always
    11 to 14 V
    D7-1 (AM2)*2 - Body ground
    G - Body ground
    Battery power supply
    Always
    11 to 14 V
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    HINT:
    1. If the result is not as specified, there may be a malfunction on the wire harness side.
    2. *1: w/o Smart Key System
    3. *2: w/ Smart Key System

  3. Reconnect the D7, D8, 1D and 1F instrument panel junction block assembly connectors.

  4. Measure the pulse according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1E-7 (LIN1)*2 - 1F-10 (GND1)
    R - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation
    D9-10 (LIN2) - 1F-10 (GND1)
    P - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation

    HINT:
    1. If the result is not as specified, the main body ECU (Instrument panel junction block assembly) may have a malfunction.
    2. *2: w/ Smart Key System


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)

B158006E16

  1. Disconnect the H1 motor connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H1-2 (B) - H1-1 (E)
    SB - W-B
    Battery power supply
    Always
    11 to 14 V
    H1-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    HINT:
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the H1 motor connector.

  4. Measure the pulse according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H1-9 (LIN) - H1-1 (E)
    P - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation

    HINT:
    If the result is not as specified, the motor may be malfunctioning.


CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) [w/ Sliding Roof]

B160074E05

  1. Disconnect the Q12 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Q12-1 (B) - Q12-2 (E)
    B - W-B
    Battery power supply
    Always
    11 to 14 V
    Q12-2 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    HINT:
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the Q12 ECU connector.

  4. Measure the pulse according to value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Q12-4 (MPX1) - Q12-2 (E)
    P - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation

    HINT:
    If the result is not as specified, the ECU may be malfunctioning.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [w/ Smart Key System]

B122343E09

  1. Disconnect the D40 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D40-1 (+B) - D40-17 (E)
    B - B
    Battery power supply
    Always
    10 to 14 V
    D40-17 (E) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω

    HINT:
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D40 ECU connector.

  4. Measure the pulse according to value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D40-10 (LIN) - D40-17 (E)
    L - B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation
    D40-18 (IG) - D40-17 (E)
    G - B
    Power supply
    Ignition switch on (IG)
    10 to 14 V
    D40-18 (IG) - D40-17 (E)
    G - B
    Power supply
    Ignition switch off
    0 V

    HINT:
    If the result is not as specified, the ECU may be malfunctioning.


CHECK ID CODE BOX (IMMOBILISER CODE ECU) [w/ Smart Key System]

B113402E03

  1. Disconnect the D31 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D31-1 (+B) - D31-8 (GND)
    W - V
    Battery power supply
    Always
    11 to 14 V
    D31-8 (GND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω

    HINT:
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D31 ECU connector.

  4. Measure the pulse according to value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D31-3 (LIN1) - D31-8 (GND)
    LG - V
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation

    HINT:
    If the result is not as specified, the ECU may be malfunctioning.


CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) [w/ Smart Key System]

B118684E12

  1. Disconnect the D11 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D11-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    D11-6 (IG2) - D11-1 (GND)
    V - W-B
    Power supply
    Ignition switch on (IG)
    10 to 14 V
    D11-6 (IG2) - D11-1 (GND)
    V - W-B
    Power supply
    Ignition switch off
    0 V
    D11-7 (B) - D11-1 (GND)
    G - W-B
    Battery power supply
    Always
    10 to 14 V

    HINT:
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D11 ECU connector.

  4. Measure the pulse according to value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D11-5 (LIN) - D11-1 (GND)
    GR - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation

    HINT:
    If the result is not as specified, the ECU may be malfunctioning.