Home › COMMUNICATION SYSTEM › MULTIPLEX COMMUNICATION › LIN COMMUNICATION SYSTEM

DTC    B2325    LIN Communication Bus Malfunction

for Preparation Click here


DESCRIPTION

The main body ECU (instrument panel junction block assembly) monitors communication between all the ECUs connected to the door system LIN bus lines. When the main body ECU (instrument panel junction block assembly) detects errors in communication with all the ECUs connected to the door system LIN bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be output.

DTC No.
DTC Detection Condition
Trouble Area
B2325
Main body ECU (instrument panel junction block assembly) detects errors in communication with the ECUs connected to the door system LIN bus lines 3 times in a row.
  1. Front power window regulator motor assembly LH
  2. Sliding roof ECU (Sliding roof drive gear sub-assembly)*1
  3. Main body ECU (Instrument panel junction block assembly)
  4. Wire harness

HINT:
*1: w/ Sliding Roof


WIRING DIAGRAM


B162901E08


INSPECTION PROCEDURE

NOTICE:
When using Techstream with the ignition switch off to troubleshoot:
Connect Techstream to the vehicle, and turn the courtesy switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - EACH ECU)

HINT:
*1: w/ Sliding Roof


B176075E02

  1. Disconnect the D9 connector.

  1. Disconnect the H1 connector.

  1. Disconnect the Q12*1 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D9-10 (LIN2) - H1-9 (LIN)
    Always
    Below 1 Ω
    D9-10 (LIN2) - Q12*1-4 (MPX1)
    Always
    Below 1 Ω
    D9-10 (LIN2) - Body ground
    Always
    10 kΩ or higher

    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D9-10 (LIN2) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.SYSTEM CHECK
  1. Check the vehicle specifications.

    Result:
    Result
    Proceed to
    Models with Sliding roof
    A
    Models without Sliding roof
    B



B
Go to step 5
A


3.CHECK FOR DTC (SLIDING ROOF ECU)
  1. Connect the D9 connector.

  1. Connect the H1 connector.

  1. Check for DTC.

    Result:
    Result
    Proceed to
    B2325 is output
    A
    B2325 is not output
    B



B
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (Click here)
A


4.CHECK FOR DTC (POWER WINDOW ECU)
  1. Connect the Q12 connector.

  1. Disconnect the H1 connector.

  1. Recheck for DTC.

    Result:
    Result
    Proceed to
    B2325 is output
    A
    B2325 is not output
    B



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
A

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) 

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
  1. Replace the front power window regulator motor assembly LH with a normally-functioning or a new one (Click here).


NEXT


6.CHECK FOR DTC
  1. Recheck for DTC.

    Result:
    Result
    Proceed to
    B2325 is not output
    A
    B2325 is output
    B



B
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
A

END