IGNITION COIL AND SPARK PLUG > INSTALLATION |
| 1. INSTALL SPARK PLUG |
![]() |
Install the 6 spark plugs.
| 2. INSTALL IGNITION COIL ASSEMBLY |
![]() |
Install the 6 ignition coils with the 6 bolts.
Connect the 6 ignition coil connectors.
![]() |
Install the 4 bolts [A].
Install the nut [B].
Install the 2 clamps [C].
| 3. INSTALL INTAKE AIR SURGE TANK ASSEMBLY |
| Tightening Parts | ||
| Intake Manifold and Intake Air Surge Tank Assembly |
![]() |
Install the surge tank with the 4 bolts and 2 nuts in the order shown in the illustration.
![]() |
Connect the 2 water by-pass hoses to the throttle with motor body assembly.
![]() |
Connect the connector.
Install the clamp and connect the throttle with motor body assembly connector.
![]() |
Connect the 4 hoses.
| 4. TEMPORARILY INSTALL NO. 1 SURGE TANK STAY |
| Tightening Parts | ||
| No. 1 Surge Tank Stay and Intake Air Surge Tank Assembly | ||
| No. 1 Surge Tank Stay and Cylinder Head Cover RH |
![]() |
Temporarily install the intake air surge tank assembly with 3 new gaskets on the intake manifold .
Temporarily install the No. 1 surge tank stay with the 2 bolts.
| 5. TEMPORARILY INSTALL THROTTLE BODY BRACKET |
| Tightening Parts | ||
| Throttle body bracket and Intake Air Surge Tank Assembly | ||
| Throttle body bracket and Cylinder Head Cover RH |
![]() |
Temporarily install the throttle body bracket with the 2 bolts.
| 6. FULLY TIGHTEN NO. 1 SURGE TANK STAY |
| Tightening Parts | ||
| No. 1 Surge Tank Stay and Intake Air Surge Tank Assembly | ||
| No. 1 Surge Tank Stay and Cylinder Head Cover RH |
![]() |
Fully tighten the 2 bolts in the order shown in the illustration.
| 7. FULLY TIGHTEN THROTTLE BODY BRACKET |
| Tightening Parts | ||
| Throttle body bracket and Intake Air Surge Tank Assembly | ||
| Throttle body bracket and Cylinder Head Cover RH |
![]() |
Fully tighten the 2 bolts in the order shown in the illustration.
| 8. CONNECT ENGINE ROOM MAIN WIRE |
![]() |
Connect the 5 harness clamps.
| 9. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Install the air cleaner filter element, align the groove on the air cleaner hose with the throttle body alignment tab and tighten the clamp as shown in the illustration.
Install the air cleaner cap with the 2 bolts and clips
![]() |
Connect the 3 vacuum hoses.
![]() |
Connect the mass air flow meter connector.
Connect the No. 2 ventilation hose and fuel vapor feed hose assembly.
| 10. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY |
![]() |
Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.
![]() |
Engage the 4 clamps.
| 11. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Install the windshield wiper motor and link assembly with the 4 bolts.
Connect the connector.
| 12. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
Engage the 20 claws.

Install the cowl top ventilator louver sub-assembly with the 2 clips.
![]() |
Engage the 2 claws and connect the front fender to cowl side seal LH.
![]() |
Engage the 2 claws and connect the front fender to cowl side seal RH.
| 13. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
When reinstalling:
![]() |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 31.9 mm (1.26 in.) |
Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.
| 14. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
When reinstalling:
![]() |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 25.6 mm (1.00 in.) |
| 15. INSTALL V-BANK COVER SUB-ASSEMBLY |
![]() |
Fit the 3 retainers and install the V-bank cover.
| 16. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the 2 cylinder block drain cock plugs.
Loosen the air drain cock plug from the water inlet housing.
![]() |
Loosen the air drain plug at the top of the radiator 3 or 4 turns.
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.
Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
| Condition | Specified Condition |
| w/ Rear Heater | 11.0 liters (11.6 US qts, 9.7 Imp. qts) |
| w/o Rear Heater | 8.8 liters (9.3 US qts, 7.7 Imp. qts) |
| Condition | Specified Condition |
| w/ Rear Heater | 11.7 liters (12.4 US qts, 10.3 Imp. qts) |
| w/o Rear Heater | 9.5 liters (10.1 US qts, 8.4 Imp. qts) |
Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the FULL line on the radiator reservoir.
| 17. INSPECT FOR ENGINE COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 18. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Install the No. 1 engine under cover with the 6 bolts and 2 clips.
| 19. INSTALL ENGINE UNDER COVER ASSEMBLY |
![]() |
Install the engine under cover assembly with the 4 bolts and 5 clips.
![]() |
Install the engine under cover assembly RR with the 2 bolts.