Home › SUSPENSION & AXLE › SUSPENSION › FRONT SUSPENSION MEMBER

FRONT SUSPENSION MEMBER > INSTALLATION

for Preparation Click here



1. INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH


    C167151E01
  1. Temporarily install a new front suspension member body mounting rear cushion LH while confirming the installation direction.

    NOTICE:
    Position the front suspension member body mounting rear cushion in the correct direction.



    C169232E01
  1. Install SST as shown in the illustration.

    SST
    09830-10010   (09830-01010, 09830-01020, 09830-01030, 09830-01060)



    C167152E01
  1. Using SST, install the front suspension member body mounting rear cushion LH as shown in the illustration.

    NOTICE:
    Check that there is no clearance between the front suspension member and the front suspension member body mounting rear cushion LH.



2. INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH


    C167150E01
  1. Temporarily install a new front suspension member body mounting rear cushion RH while confirming the installation direction.

    NOTICE:
    Position the front suspension member body mounting rear cushion in the correct direction.

  1. Using SST, install the front suspension member body mounting rear cushion RH.

    SST
    09830-10010   (09830-01010, 09830-01020, 09830-01030, 09830-01060)

    HINT:
    Perform the same procedure as the LH side.



3. INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION


    C167147E01
  1. Temporarily install a new front suspension member body mounting front cushion while confirming the installation direction.

    NOTICE:
    Position the front suspension member body mounting front cushion in the correct direction.



    C167148E01
  1. Using SST, install the front suspension member body mounting front cushion as shown in the illustration.

    SST
    09830-10010   (09830-01010, 09830-01020, 09830-01030, 09830-01060)

    NOTICE:
    Check that there is no clearance between the front suspension member and the front suspension member body mounting rear cushion.



4. INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER


5. INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER


6. INSTALL FRONT SUSPENSION MEMBER DYNAMIC DAMPER


    C167144
  1. Install the front suspension member dynamic damper with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



7. INSTALL FRONT LOWER SUSPENSION ARM LH
  1. Install the front lower arm bushing stopper to the front lower suspension arm.

  1. Install the front lower suspension arm to the front frame assembly with the 3 bolts and nut, but do not tighten them yet.



    C167143E01
  1. Tighten the 3 bolts in numerical order shown in the illustration.

    Torque:
    Bolt 1, 2:
    200 N*m{ 2039 kgf*cm , 147 ft.*lbf }
    Bolt 3:
    206 N*m{ 2100 kgf*cm , 152 ft.*lbf }

    HINT:
    Start installing the bolts from the front side of the vehicle.



8. INSTALL FRONT LOWER SUSPENSION ARM RH

HINT:
Perform the same procedure as the LH side.



9. INSTALL TRANSVERSE ENGINE MOUNTING INSULATOR


    A171844
  1. Install the transverse engine mounting insulator with the 2 nuts.

    Torque:
    52 N*m{ 525 kgf*cm , 38 ft.*lbf }



    A171843
  1. Install the 2 hole plugs.



10. INSTALL FRONT FRAME ASSEMBLY


  1. Temporarily install the engine assembly with transaxle with the 9 nuts and 2 bolts.


    A172974E01



    A172975E01
  1. Tighten the 4 nuts.

    Torque:
    A:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }
    B:
    52 N*m{ 525 kgf*cm , 38 ft.*lbf }



    A172976E01
  1. Tighten the 4 nuts.

    Torque:
    A:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }
    B:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }



    A172977E01
  1. Tighten the 4 nuts.

    Torque:
    A:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }
    B:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }



    A171830
  1. Tighten the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }



    A171835
  1. Connect the duty vacuum switching valve connector and clamp.



  1. Install the 5 hole plugs.


    A172972E01



11. REMOVE ENGINE HANGERS


    A129635E01
  1. Remove the 4 bolts and 2 engine hangers.



12. INSTALL POWER STEERING LINK ASSEMBLY


    C166343
  1. Install the power steering link assembly with the 2 bolts and 2 nuts.

    Torque:
    70 N*m{ 713 kgf*cm , 51 ft.*lbf }

    NOTICE:
    1. Make sure to tighten the bolts starting from the left side of the vehicle.
    2. Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed.



13. INSTALL FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY


14. INSTALL NO. 1 FRONT STABILIZER BRACKET LH


    C167140
  1. Install the No. 1 front stabilizer bracket LH to the front frame assembly with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



15. INSTALL NO. 1 FRONT STABILIZER BRACKET RH

HINT:
Perform the same procedure as the LH side.



16. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

HINT:
Install engine assembly with trans axle (Click here).