Home › SUSPENSION & AXLE › SUSPENSION › FRONT SUSPENSION MEMBER

FRONT SUSPENSION MEMBER > REMOVAL

for Preparation Click here



1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

HINT:
Remove engine assembly with transaxle (Click here).



2. REMOVE NO. 1 FRONT STABILIZER BRACKET LH


    C167140
  1. Remove the 2 bolts and the No. 1 front stabilizer bracket LH from the front frame assembly.



3. REMOVE NO. 1 FRONT STABILIZER BRACKET RH

HINT:
Perform the same procedure as the LH side.



4. REMOVE FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY


5. REMOVE POWER STEERING LINK ASSEMBLY


    C166343
  1. Remove the 2 bolts, 2 nuts, and power steering link assembly.

    NOTICE:
    Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut fixed.



6. INSTALL ENGINE HANGERS


    A129635E01
  1. Install the 2 engine hangers with the 4 bolts as shown in the illustration.

    Part No.:
    No. 1 engine hanger 12281-31120
    No. 2 engine hanger 12282-31100
    Bolts 91671-10825

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

  1. Attach the engine sling device and hang the engine with the chain block.



7. REMOVE FRONT FRAME ASSEMBLY


    A171835
  1. Disconnect the active mount VSV connector and harness clamp.



  1. Loosen the 3 nuts.


    A172971E01



  1. Remove the 5 hole plugs.


    A172972E01



  1. Remove the 9 nuts.


    A172973E01



    A171830
  1. Remove the 2 bolts and separate the engine with transaxle from the front frame assembly.



8. REMOVE TRANSVERSE ENGINE MOUNTING INSULATOR


    A171843
  1. Remove the 2 hole plugs.



    A171844
  1. Remove the 2 nuts and transverse engine mounting insulator.



9. REMOVE FRONT LOWER SUSPENSION ARM LH


    C167143
  1. Remove the 3 bolts, nut, and the front lower suspension arm from the front frame assembly.

  1. Remove the front lower arm bushing stopper from the front lower suspension arm.



10. REMOVE FRONT LOWER SUSPENSION ARM RH

HINT:
Perform the same procedure as the LH side.



11. REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER


    C167144
  1. Remove the 2 bolts and front suspension member dynamic damper.



12. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER


13. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER


14. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION


    C169231E01
  1. Install SST as shown in the illustration.

    SST
    09830-10010   (09830-01010, 09830-01040, 09830-01050)
    09950-40011   (09951-04020, 09952-04010, 09955-04011)



    C167146E01
  1. Using SST, remove the front suspension member body mounting front cushion.

    NOTICE:
    1. Make sure that the claws of SST are securely hung onto the mounting cushion.
    2. Tighten SST slowly and evenly.
    3. Be careful as the mounting cushion may fly out.
    4. The mounting cushion cannot be reused.



15. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH


    C167149E01
  1. Using SST, remove the front suspension member body mounting rear cushion LH.

    SST
    09830-10010   (09830-01010, 09830-01040, 09830-01050)
    09950-40011   (09951-04020, 09952-04010, 09954-04010, 09955-04011)

    NOTICE:
    1. Make sure that the claws of SST are securely hung onto the mounting cushion.
    2. Tighten SST slowly and evenly.
    3. Be careful as the mounting cushion may fly out.
    4. The mounting cushion cannot be reused.



16. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH

HINT:
Perform the same procedure as the LH side.

SST
09830-10010   (09830-01010, 09830-01040, 09830-01050)
09950-40011   (09951-04020, 09952-04010, 09954-04010, 09955-04011)