FRONT SEAT ASSEMBLY (for Power Seat) > DISASSEMBLY |
| 1. REMOVE RECLINING POWER SEAT SWITCH KNOB |
![]() |
Using a screwdriver wrapped with protective tape, disengage the 2 claws and remove the reclining power seat switch knob.
| 2. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
![]() |
Using a screwdriver wrapped with protective tape, disengage the 4 claws and remove the slide and vertical power seat switch knob.
| 3. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY |
![]() |
Disengage the hooks.
![]() |
Remove the 5 screws.
Disengage the claw.
Disengage the guide and remove the front seat cushion shield assembly.
w/o Seat Cushion Front Edge Adjustment Function:
Disconnect the connector from the front power seat lumbar switch.
w/ Seat Cushion Front Edge Adjustment Function:
Disconnect the connector from the front power seat lumbar switch and the seat variable cushion switch.
Disengage each clamp.
| 4. REMOVE FRONT INNER NO. 1 SEAT CUSHION SHIELD |
![]() |
Remove the 2 screws.
Disengage the 2 claws and remove the front inner No. 1 seat cushion shield.
| 5. REMOVE FRONT POWER SEAT LUMBAR SWITCH |
![]() |
Remove the 2 screws and the front power seat lumbar switch.
| 6. REMOVE SEAT VARIABLE CUSHION SWITCH (w/ Seat Cushion Front Edge Adjustment Function) |
![]() |
Remove the 2 screws and the seat variable cushion switch.
| 7. REMOVE POWER SEAT SWITCH |
![]() |
Remove the 3 screws.
Disconnect the connector and remove the power seat switch.
| 8. REMOVE FRONT SEAT INNER BELT ASSEMBLY |
Disconnect each connector and clamp.
![]() |
Remove the nut and the front seat inner belt assembly.
| 9. REMOVE FRONT SEAT CUSHION INNER SHIELD |
![]() |
Remove the screw.
Disengage the claw.
![]() |
Disengage the guide and remove the front seat cushion inner shield as shown in the illustration.
| 10. REMOVE FRONT SEAT CUSHION COVER WITH PAD (w/o Seat Cushion Front Edge Adjustment Function) |
![]() |
Disengage the hooks.
Disengage the 2 clamps.
w/ Seat Heater System:
Disengage each clamp of the seat heater wire harness.
Disconnect the seat heater connector.
Using a clip remover, remove the 2 clips.

Disengage the hooks and remove the front seat cushion cover with pad as shown in the illustration.
| 11. REMOVE FRONT SEAT CUSHION COVER WITH PAD (w/ Seat Cushion Front Edge Adjustment Function) |
![]() |
Disengage the 4 clamps.
Disengage the hooks.
Disconnect the 2 connectors.
Using a clip remover, remove the 2 clips

Disengage the hooks as shown in the illustration.
![]() |
Disengage the hook as shown in the illustration.
![]() |
Remove the 4 hog rings and the front seat cushion cover with pad.
| 12. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Seat Cushion Front Edge Adjustment Function) |
![]() |
Remove the 6 hog rings.
![]() |
Remove the 11 hog rings and the separate type front seat cushion cover.
| 13. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Seat Cushion Front Edge Adjustment Function) |
![]() |
Remove the 2 hog rings.
![]() |
Remove the 15 hog rings and the separate type front seat cushion cover.
| 14. REMOVE FRONT SEATBACK COVER WITH PAD |
![]() |
Remove the 3 hog rings.
![]() |
Remove the 5 hog rings.
![]() |
Disengage the 2 hooks.
![]() |
Turn back the separate type front seatback cover to remove the nut, and separate the bracket of the separate type front seatback cover.
![]() |
Disengage the 4 claws and remove the 2 front seat headrest supports.
Remove the separate type front seatback cover with pad from the front seat frame assembly with adjuster.
| 15. REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Remove the 7 hog rings and the separate type front seatback cover.
| 16. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 2 screws and the lumbar support adjuster assembly.
![]() |
Remove the bush.
| 17. REMOVE LUMBAR SUPPORT MOTOR ASSEMBLY |
![]() |
Remove the 4 screws and the lumbar support motor assembly.
| 18. REMOVE ACTIVE HEADREST UPPER UNIT |
![]() |
Remove the nut and disconnect the cable from the active headrest upper unit as shown in the illustration.
Remove the 4 nuts and the active headrest upper unit.
| 19. REMOVE ACTIVE HEADREST LOWER UNIT |
![]() |
Remove the 4 nuts and the active headrest lower unit.
| 20. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw.
Disengage the clamp.
Disengage the guide and remove the reclining adjuster inside cover LH.
| 21. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw and the reclining adjuster inside cover LH.
| 22. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
![]() |
Remove the screw.
Disengage the clamp.
Disengage the guide and remove the reclining adjuster inside cover RH.
| 23. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
![]() |
| 24. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH |
![]() |
Remove the screw.
Disengage the hook as shown in the illustration.
Disengage the guide and remove the front seat lower cushion shield LH .
| 25. REMOVE FRONT SEAT LOWER CUSHION SHIELD RH |
![]() |
Remove the screw.
Disengage the hook as shown in the illustration.
Disengage the guide and remove the front seat lower cushion shield RH.
| 26. REMOVE FRONT SEAT WIRE (w/o Seat Cushion Front Edge Adjustment Function) |
![]() |
Disengage the 2 clamps.
Disconnect the connector.
w/o Seat Heater System:
![]() |
Disengage the 4 clamps.
Disengage the 2 claws.
Disconnect the 4 connectors and remove the front seat wire.
w/ Seat Heater System:
![]() |
Disengage the 4 clamps.
Disengage the 2 claws.
Disconnect the 5 connectors and remove the front seat wire.
| 27. REMOVE FRONT SEAT WIRE (w/ Seat Cushion Front Edge Adjustment Function) |
![]() |
Disengage the 2 clamps.
Disconnect the connector.
w/o Seat Heater System:
![]() |
Disengage the 4 clamps.
Disengage the 2 claws.
Disconnect the 5 connectors and remove the front seat wire.
w/ Seat Heater System:
![]() |
Disengage the 4 clamps.
Disengage the 2 claws.
Disconnect the 6 connectors and remove the front seat wire.
| 28. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System) |
![]() |
Disengage the 2 clamps and remove the seat heater control sub-assembly.
| 29. REMOVE SEAT POSITION SENSOR |
![]() |
Disconnect the connector.
Using a "TORX" socket wrench (T30), remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.
![]() |
Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.
| 30. REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) |
![]() |
Disconnect the 2 connectors from the occupant classification ECU.
Disengage the claw and remove the occupant classification ECU.