Home › BODY ELECTRICAL › WIPER AND WASHER › WASHER MOTOR (for Rear Side)

WASHER MOTOR (for Rear Side) > REMOVAL

for Preparation Click here



1. REMOVE ENGINE UNDER COVER ASSEMBLY


    A171849
  1. Remove the 2 bolts and engine under cover assembly RR.



    A171850
  1. Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.



2. REMOVE NO. 1 ENGINE UNDER COVER


    A171855
  1. Remove the 6 bolts, 2 clips and No. 1 engine under cover.



3. REMOVE COOL AIR INTAKE DUCT SEAL


    B172745
  1. Remove the 11 clips and cool air intake duct seal.



4. REMOVE RADIATOR GRILLE


    B172749E01
  1. Put protective tape around the radiator grille.



    B172746
  1. Remove the 2 bolts and 4 clips.



    B172747
  1. Disengage the 6 claws and 4 guides, and remove the radiator grille.



5. REMOVE FRONT BUMPER ASSEMBLY (w/o Fog Light)


    B172760E01
  1. Put protective tape around the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.



    B172761E01
  1. Remove the screw.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.



    B172763
  1. Remove the 7 screws and clip.



    B172764
  1. Disengage the 4 claws and disconnect the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Remove the front bumper assembly.



6. REMOVE FRONT BUMPER ASSEMBLY (w/ Fog Light)


    B172760E01
  1. Put protective tape around the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.



    B172761E01
  1. Remove the screw.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.



    B172763
  1. Remove the 7 screws and clip.



    B172764
  1. Disengage the 4 claws and disconnect the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disconnect each fog light connector, and then remove the front bumper assembly.



7. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH


    A176043
  1. Remove the clip.

  1. Using a 4 mm hexagon wrench, remove the screw.



    A176044
  1. Peel off the front fender side protector and disengage the 3 clips, and then remove the front fender moulding sub-assembly RH.

  1. Remove the pad from the front fender moulding sub-assembly RH.

  1. Remove the 2 clips No. 4 from the front fender moulding sub-assembly RH.



    A176045
  1. Remove the front fender side protector from the front fender moulding sub-assembly RH.



8. REMOVE FRONT FENDER LINER RH


    B174753E01
  1. Remove the screw.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.



    B174750
  1. Using a 4 mm hexagon wrench, remove the 2 screws.

  1. Remove the 2 grommets.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.



    B174752
  1. Remove the 5 clips, 7 screws and front fender liner RH.



9. DRAIN WASHER FLUID


    E150185
  1. Disconnect the washer hose from the rear washer motor and pump assembly, and drain the washer fluid.



10. REMOVE REAR WASHER MOTOR AND PUMP ASSEMBLY


    E150197E01
  1. Disconnect the connector.

  1. Remove the rear washer motor and pump assembly.