WASHER LEVEL WARNING SWITCH > INSTALLATION |
| 1. INSTALL LEVEL WARNING SWITCH ASSEMBLY |
![]() |
Install the level warning switch assembly.
Connect the connector.
| 2. FILL WASHER JAR WITH WASHER FLUID |
![]() |
Connect the washer hose to the front washer motor and pump assembly and fill the washer jar with washer fluid.
| 3. INSTALL FRONT FENDER LINER RH |
![]() |
Install the front fender liner RH with the 5 clips and 7 screws.
![]() |
Install 2 new grommets.
Using a 4 mm hexagon wrench, install the 2 screws.
![]() |
Install the screw and pin hold clip.
| 4. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY RH |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove the front fender side protector from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
![]() |
Clean the front fender moulding sub-assembly RH. (If reusing the front fender moulding sub-assembly RH)
Using a heat light, heat the front fender moulding sub-assembly RH.
Remove the front fender side protector from the front fender moulding sub-assembly RH.
Wipe off any tape adhesive residue with cleaner.
Install a new front fender side protector to the the front fender moulding sub-assembly RH.
![]() |
Install the front fender moulding sub-assembly RH.
Using a heat light, heat the vehicle body and the front fender moulding sub-assembly.
Remove the release paper from the front fender moulding sub-assembly.
Engage the 3 clips and install the front fender moulding sub-assembly RH.
![]() |
Using a 4 mm hexagon wrench, install the screw.
Install the clip.
| 5. INSTALL FRONT BUMPER ASSEMBLY (w/o Fog Light) |
![]() |
Engage the 4 claws and install the front bumper assembly.
![]() |
Install the clip and 7 screws.
![]() |
Install the screw and pin hold clip.
| 6. INSTALL FRONT BUMPER ASSEMBLY (w/ Fog Light) |
Connect each fog light connector, and then install the front bumper assembly.
![]() |
Engage the 4 claws.
![]() |
Install the clip and 7 screws.
![]() |
Install the screw and pin hold clip.
| 7. INSTALL RADIATOR GRILLE |
![]() |
Engage the 4 guides and 6 claws, and install the radiator grille.
![]() |
Install the 4 clips and 2 bolts.
| 8. INSTALL COOL AIR INTAKE DUCT SEAL |
![]() |
Install the cool air intake duct seal with the 11 clips.
| 9. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Install the No. 1 engine under cover with the 6 bolts and 2 clips.
| 10. INSTALL ENGINE UNDER COVER ASSEMBLY |
![]() |
Install the engine under cover assembly with the 4 bolts and 5 clips.
![]() |
Install the engine under cover assembly RR with the 2 bolts.
| 11. VEHICLE PREPARATION FOR FOG LIGHT AIMING ADJUSTMENT (w/ Fog Light) |
Prepare the vehicle:
| 12. PREPARATION FOR FOG LIGHT AIMING (w/ Fog Light) |
![]() |
Prepare the vehicle:
Prepare a piece of thick white paper (approximately 2 m (6.6 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.
Draw a vertical line down the center of the screen (V line).
Set the screen as shown in the illustration.

![]() |
Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.
H Line (Fog light height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.
V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):
Draw two vertical lines so that they intersect the H line at each center mark aligned with the center of the fog light bulbs.
| 13. INSPECT FOG LIGHT AIMING (w/ Fog Light) |
Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.
Start the engine.
Turn on the fog light and check if the cutoff line falls within the specified area in the following illustration.

| 14. ADJUST FOG LIGHT AIMING (w/ Fog Light) |
![]() |
Adjust the aim vertically:
Adjust the aim of each fog light to the specified range by turning each aiming screw with a screwdriver.