Home › RESTRAINTS › SEAT BELT › REAR NO. 1 SEAT INNER BELT ASSEMBLY (for LH Side)

REAR NO. 1 SEAT INNER BELT ASSEMBLY (for LH Side) > INSTALLATION

for Preparation Click here



1. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY


    B170974
  1. Install the rear No. 1 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



2. INSTALL REAR SEAT RECLINING INNER COVER


    B206105
  1. Engage the guide.

  1. Install the rear seat reclining inner cover with the screw.



3. INSTALL SEAT TRACK UPPER RAIL COVER


    B206104
  1. Engage the claw.

  1. Install the seat track upper rail cover with the screw.



4. INSTALL REAR NO. 1 SEAT CUSHION COVER WITH PAD


    B173833E01
  1. Using hog ring pliers, install 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B206101
  1. Engage the 12 hooks.



    B196379
  1. Engage the 3 buttons.



    B173832E01
  1. Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.

  1. Install the 2 hooks.



    B180396
  1. Engage the 2 hooks to install the rear No. 1 seat cushion cover with pad.



5. INSTALL REAR SEAT CUSHION MOULDING RH


    B173788
  1. Engage the 6 claws.

  1. Install the rear seat cushion moulding RH with the screw.



6. INSTALL SEAT ADJUSTER COVER CAP


    B173787
  1. Engage the 2 claws to install the seat adjuster cover cap.



7. INSTALL REAR SEAT CUSHION MOULDING LH


    B196365
  1. Engage the guide.

  1. Engage the 5 claws.

  1. Install the rear seat cushion moulding LH with the screw.



8. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE


    B196364
  1. Install the No. 1 reclining adjuster release handle with the 3 screws.



9. INSTALL REAR SEAT RECLINING UPPER COVER


    B173784
  1. Engage the 3 claws to install the rear seat reclining upper cover.



10. INSTALL REAR NO. 1 SEAT ASSEMBLY


    B173778
  1. Temporarily install the 2 bolts on the front side of the seat.



    B173780
  1. Temporarily install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



11. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY (w/ Remote Folding Function)


  1. Remove the rear seat reclining control cable from the carpet hole.


    B180395E01

  1. Connect the rear seat reclining control cable as shown in the illustration.



  1. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.


    B173771E01



    B174591
  1. Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Return the seatback to the upright position.



  1. Pull up the adjuster's lock piece to lock it as shown in the illustration.


    B180389E01

    NOTICE:
    When pressing the lock piece, make sure the adjuster's spring is not compress.



12. INSPECT REAR SEAT SLIDE ADJUSTER LOCK
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.



13. INSTALL REAR SEAT LEG SIDE COVER


    B173779
  1. Engage the clip.

  1. Engage the 3 claws and install the rear seat leg side cover.



14. INSTALL REAR INNER TRACK BRACKET COVER


    B173777
  1. Engage the 4 claws and install the rear inner track bracket cover.



15. INSTALL REAR OUTER TRACK BRACKET COVER


    B173776
  1. Engage the 4 claws and install the rear outer track bracket cover.



16. INSTALL REAR SEAT TRACK BRACKET COVER


    B173775
  1. Engage the 8 claws and install the 2 rear seat track bracket covers.



17. INSTALL REAR SEAT HEADREST ASSEMBLY


    B176351
  1. Install the rear seat headrest assembly as shown in the illustration.



18. INSTALL REAR CENTER SEAT ASSEMBLY