REAR NO. 1 SEAT ASSEMBLY (for LH Side) > REASSEMBLY |
| 1. INSTALL REAR SEAT CUSHION SPRING ASSEMBLY |
![]() |
Using a T45 "TORX" socket wrench, install the rear seat cushion spring assembly with the 4 bolts and 2 bushes.
| 2. INSTALL REAR SEAT HOOK |
![]() |
Engage the claw to install the rear seat hook.
| 3. INSTALL NO. 2 REAR SEAT RECLINING CONTROL CABLE |
![]() |
Engage the claw.
Engage the rear seat hook.
Engage the 4 cable clamps to install the No. 2 rear seat reclining control cable.
| 4. INSTALL NO. 1 REAR SEAT RECLINING CONTROL CABLE (w/ Remote Folding Function) |
![]() |
Install the clamp.
Engage the 2 clamps.
Engage the 6 cable clamps to install the No. 1 rear seat reclining control cable.
| 5. INSTALL NO. 2 REAR SEAT COVER |
![]() |
Install the No. 2 rear seat cover.
| 6. INSTALL REAR SEAT CUSHION SIDE COVER |
![]() |
Engage the claw.
Install the rear seat cushion side cover with the 2 screws.
| 7. INSTALL REAR NO. 2 SEATBACK COVER |
![]() |
Engage the claw.
Install the rear No. 2 seatback cover with the 2 screws.
| 8. INSTALL REAR NO. 1 SEAT SHOULDER BELT COVER |
![]() |
Engage the guide.
Engage the claw to install the rear No. 1 seat shoulder belt cover.
| 9. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY |
![]() |
Install the rear center seat outer belt assembly with the bolt and nut.
| 10. INSTALL BELT SUPPORT PLATE |
![]() |
Engage the 3 claws to install the belt support plate.
| 11. INSTALL SEPARATE TYPE REAR NO. 1 SEATBACK COVER |
![]() |
Using hog ring pliers, install the separate type rear No. 1 seatback cover with 10 new hog rings.
| 12. INSTALL REAR NO. 1 SEATBACK COVER WITH PAD |
![]() |
Engage the hooks to install the rear No. 1 seatback cover with pad.
| 13. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY RH |
![]() |
Engage the 2 claws to install the rear No. 1 seat headrest support assembly RH.
| 14. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY LH |
![]() |
Engage the 2 claws to install the rear No. 1 seat headrest support assembly LH.
| 15. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY |
![]() |
Engage 2 guides.
Engage the 2 clips.
Engage the 19 claws to install the rear seatback board carpet assembly as shown in the illustration.
| 16. INSTALL REAR SEATBACK LOCK ASSEMBLY |
![]() |
Install the rear seatback lock assembly with the 2 bolts.
| 17. INSTALL REAR SEATBACK LOWER LOCK BEZEL |
![]() |
Install the rear seatback lower lock bezel with the 2 screws.
![]() |
Engage the snap to install the rear seat track handle as shown in the illustration.
![]() |
Engage the 4 claws.
Install the rear center seat outer belt cover with the screw.
| 18. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY |
![]() |
Connect the rear center seat outer belt with the bolt.
| 19. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY |
Connect the rear seat lock control cable as shown in the illustration.

![]() |
Engage the guide.
Install the rear seat lock control lever sub-assembly with the 2 screws.
| 20. INSTALL REAR SEAT LOCK STRIKER COVER |
![]() |
Engage the guide.
Engage the claw to install the rear seat lock striker cover.
| 21. INSTALL REAR SEATBACK COVER |
![]() |
Engage the 4 claws to install the rear seatback cover.
| 22. INSTALL TONNEAU COVER HOOK HOLDER |
![]() |
Install the 2 tonneau cover hook holders with the 2 screws.
| 23. INSTALL REAR SEAT ARMREST ASSEMBLY |
![]() |
Install the rear seat armrest assembly with the bolt.
| 24. INSTALL NO. 1 SEAT ARMREST CAP |
![]() |
Engage the 2 claws to install the No. 1 seat armrest cap.
| 25. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY |
![]() |
Install the rear No. 1 seat inner belt assembly with the bolt.
| 26. INSTALL REAR SEAT RECLINING INNER COVER |
![]() |
Engage the guide.
Install the rear seat reclining inner cover with the screw.
| 27. INSTALL SEAT TRACK UPPER RAIL COVER |
![]() |
Engage the claw.
Install the seat track upper rail cover with the screw.
| 28. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Engage the guide to install the reclining adjuster inside cover LH.
| 29. INSTALL REAR SEAT NO. 1 RECLINING COVER |
![]() |
Engage the 2 guides.
Engage the claw.
Install the rear seat No. 1 reclining cover with the screw.
| 30. INSTALL NO. 1 REAR SEAT COVER (for Rear Side) |
![]() |
Engage the 2 hooks to install the No. 1 rear seat cover.
| 31. INSTALL NO. 1 REAR SEAT COVER (for RH Side) |
![]() |
Engage the 2 hooks to install the No. 1 rear seat cover.
| 32. INSTALL NO. 1 REAR SEAT COVER (for LH Side) |
![]() |
Engage the 4 hooks to install the No. 1 rear seat cover.
| 33. INSTALL SEPARATE TYPE REAR NO. 1 SEAT CUSHION COVER |
![]() |
Using hog ring pliers, install the separate type rear No. 1 seat cushion cover with 11 new hog rings.
| 34. INSTALL REAR NO. 1 SEAT CUSHION COVER WITH PAD |
![]() |
Using hog ring pliers, install 3 new hog rings.
![]() |
Engage the 12 hooks.
![]() |
Engage the 3 buttons.
![]() |
Using hog ring pliers, install 2 new hog rings.
Install the 2 hooks.
![]() |
Engage the 2 hooks to install the rear No. 1 seat cushion cover with pad.
| 35. INSTALL REAR SEAT FRONT CUSHION MOULDING |
![]() |
Install the rear seat front cushion moulding with the screw.
| 36. INSTALL REAR SEAT LOCK ASSEMBLY |
![]() |
Install the rear seat lock assembly with the 2 bolts.
| 37. INSTALL NO. 2 REAR SEAT BEZEL COVER |
![]() |
Temporarily install the No. 2 rear seat bezel cover as shown in the illustration.
Engage the 2 guides.
Install the rear seat bezel cover with the screw.
| 38. INSTALL REAR SEAT CUSHION UNDER COVER |
![]() |
Engage the guide.
Engage the claw to install the rear seat cushion under cover.
| 39. INSTALL REAR SEAT 3 POINT TYPE COVER ASSEMBLY |
![]() |
Engage the 2 claws to install the rear seat 3 point type cover assembly.
| 40. INSTALL REAR SIDE SEAT BAND SUB-ASSEMBLY |
![]() |
Install the rear side seat band sub-assembly.
| 41. INSTALL NO. 2 SEAT LEG COVER |
![]() |
Install the No. 2 seat leg cover with the 5 screws.
| 42. INSTALL REAR SEAT NO. 2 LEG SIDE COVER |
![]() |
Engage the 2 claws to install the rear seat No. 2 leg side cover.
| 43. INSTALL CENTER PROTECTOR COVER |
![]() |
Temporarily install the center protector cover.
install the rear side seat band sub-assembly with the screw.
![]() |
Engage the claw and guide.
Install the center protector cover with the screw.
| 44. INSTALL SEAT ADJUSTER COVER CAP |
![]() |
Engage the 2 claws to install the seat adjuster cover cap.
| 45. INSTALL SEAT ADJUSTER COVER CAP |
![]() |
Engage the 2 claws to install the seat adjuster cover cap.
| 46. INSTALL REAR SEAT CUSHION MOULDING RH |
![]() |
Engage the 6 claws.
Install the rear seat cushion moulding RH with the screw.
| 47. INSTALL SEAT ADJUSTER COVER CAP |
![]() |
Engage the 2 claws to install the seat adjuster cover cap.
| 48. INSTALL REAR SEAT CUSHION MOULDING LH |
![]() |
Engage the guide.
Engage the 5 claws.
Install the rear seat cushion moulding LH with the screw.
| 49. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE |
![]() |
Install the No. 1 reclining adjuster release handle with the 3 screws.
| 50. INSTALL REAR SEAT RECLINING UPPER COVER |
![]() |
Engage the 3 claws to install the rear seat reclining upper cover.