REAR NO. 2 SEAT ASSEMBLY > REASSEMBLY |
| 1. INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY |
![]() |
Temporarily install the 2 bolts <C>, 2 washers and the No. 2 seat cushion frame sub-assembly.
Temporarily install the 2 bolts <B> and the 2 bushes.
Temporarily install the 2 nuts, 2 bolts <A>, 2 springs and the 2 E-rings.
Tighten the 2 nuts, 2 bolts <B> and the 2 bolts <C> to install the No. 2 seat cushion frame sub-assembly.
| 2. INSTALL NO. 1 REAR SEAT LOCK CABLE ASSEMBLY RH |
![]() |
Connect the 2 cable clamps to install the No. 1 rear seat lock cable assembly RH.
| 3. INSTALL NO. 2 REAR SEAT CUSHION LOCK CABLE ASSEMBLY RH |
![]() |
Connect the 2 cable clamps and install the No. 2 rear seat cushion lock cable assembly RH.
Install a new clamp.
| 4. INSTALL NO. 1 REAR SEAT LOCK CABLE ASSEMBLY LH |
![]() |
Connect the 2 cable clamps to install the No. 1 rear seat lock cable assembly LH.
| 5. INSTALL NO. 2 REAR SEAT CUSHION LOCK CABLE ASSEMBLY LH |
![]() |
Connect the 2 cable clamps and install the No. 2 rear seat cushion lock cable assembly LH.
Install a new clamp.
| 6. INSTALL REAR SEATBACK EDGE PROTECTOR |
![]() |
Engage the 8 claws to install the 4 rear seatback edge protectors.
| 7. INSTALL REAR NO. 2 SEAT HEADREST ASSEMBLY RH |
![]() |
Install the rear No. 2 seat headrest assembly RH with the 3 nuts.
Connect the 2 cable clamps.
![]() |
Install the rear No. 2 seat headrest cover RH with the 2 screws.
| 8. INSTALL REAR NO. 2 SEAT HEADREST ASSEMBLY LH |
![]() |
Install the rear No. 2 seat headrest assembly LH with the 3 nuts.
Connect the 2 cable clamps.
![]() |
Install the rear No. 2 seat headrest cover LH with the 2 screws.
| 9. INSTALL NO. 2 REAR SEAT RECLINING COVER RH |
![]() |
Engage the guide.
Install the No. 2 rear seat reclining cover RH with the screw.
| 10. INSTALL NO. 2 REAR SEAT RECLINING COVER LH |
![]() |
Engage the guide.
Install the No. 2 rear seat reclining cover LH with the screw.
| 11. INSTALL REAR NO. 2 SEATBACK COVER SUB-ASSEMBLY |
Using hog ring pliers, install the rear No. 2 seatback cover sub-assembly with 18 new hog rings.

| 12. INSTALL REAR NO. 2 SEATBACK COVER WITH PAD |
Temporarily install the rear No. 2 seatback cover with pad to the rear No. 2 seatback frame sub-assembly.
![]() |
Engage the 16 clips and install the rear No. 2 seatback cover.
Engage the 15 hooks.

Using hog ring pliers, install the rear No. 2 seatback cover with pad with 4 new hog rings.
| 13. INSTALL NO. 1 REAR SEAT COVER BEZEL |
![]() |
Install the No. 1 rear seat cover bezel to the No. 1 rear side seat band sub-assembly.
![]() |
Engage the hook.
Install the No. 1 rear seat cover bezel and the No. 1 rear side seat band sub-assembly with the 2 screws.
| 14. INSTALL NO. 2 SEATBACK BOARD SUB-ASSEMBLY |
Engage the 3 hooks.

Engage the 7 clips to install the No. 2 seatback board sub-assembly.
| 15. INSTALL REAR NO. 2 SEAT HANDLE |
Connect the 2 cable clamps as shown in the illustration.

![]() |
Install a new clamp.
![]() |
Install the rear No. 2 seat handle with the 2 screws.
| 16. INSTALL REAR SEAT LOCK STRIKER COVER |
![]() |
Engage the 2 guides.
Engage the claw to install the rear seat lock striker cover.
| 17. INSTALL NO. 1 REAR SIDE SEAT BAND SUB-ASSEMBLY |
![]() |
Attach the fastener.
Install the seat track handle with the 2 new clips.
| 18. INSTALL REAR NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY |
Using hog ring pliers, install the rear No. 2 seat cushion cover sub-assembly with 14 new hog rings.

| 19. INSTALL REAR NO. 2 SEAT CUSHION COVER WITH PAD |
Using hog ring pliers, install 4 new hog rings.

Engage the 13 hooks to install the rear No. 2 seat cushion cover with pad.

| 20. INSTALL NO. 2 SEAT HINGE COVER RH |
![]() |
Install the No. 2 seat hinge cover RH with the 2 screws.
| 21. INSTALL RECLINING COVER PROTECTOR RH |
![]() |
Install the reclining cover protector RH with the 2 screws.
| 22. INSTALL NO. 2 SEAT HINGE COVER LH |
![]() |
Install the No. 2 seat hinge cover LH with the 2 screws.
| 23. INSTALL RECLINING COVER PROTECTOR LH |
![]() |
Install the reclining cover protector LH with the 2 screws.