Home › BODY › WINDSHIELD / WINDOWGLASS › BACK WINDOW LOCK

BACK WINDOW LOCK > INSTALLATION

for Preparation Click here



1. PRECAUTION

NOTICE:
  1. Be sure to use the centering jig when removing and installing the rear wiper motor assembly (for Glass Hatch Type). Failure to do so will result in a change of the location of the axis of the rear wiper motor assembly (for Glass Hatch Type), causing the wiping angle to change.
  2. After installing the rear wiper motor assembly (for Glass Hatch Type), do not open the glass hatch before installing the rear wiper link pivot.
  3. If the rear wiper motor assembly is removed without using the centering jig, the rear wiper motor assembly must be replaced with a new one.



2. INSTALL BACK WINDOW LOCK ASSEMBLY


    B173455
  1. Engage the clip and install the back window lock assembly.



    B173454
  1. Install the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B173453
  1. Engage the clamp.

  1. Connect the connector.



3. INSTALL REAR WIPER MOTOR ASSEMBLY


    E151099E01
  1. Temporarily install the rear wiper motor assembly with the 4 bolts and 2 nuts.

    NOTICE:
    1. Do not hold the rear wiper motor assembly by the rear wiper link pivot.
    2. Be careful not to scratch the back door glass.
    3. Do not remove the centering jig before installing the rear wiper link pivot.

  1. Tighten the 4 bolts and 2 nuts in the order shown in the illustration to install the rear wiper motor assembly.

    Torque:
    Bolt:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
    Nut:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



4. INSTALL REAR WIPER LINK PIVOT


    E150158
  1. Install the rear wiper link pivot with the nut.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Open the glass hatch.



    E154835
  1. Disengage the 2 guides.

  1. Disengage the 3 claws and remove the centering jig.

  1. Close the glass hatch.



5. INSTALL REAR WIPER LINK CAP


    E150184E01
  1. Apply MP grease to the entire surface of the rear wiper link cap.

    HINT:
    Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.



    E150157
  1. Install the rear wiper link cap.



6. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY
  1. Stop the wiper motor at the automatic stop position.



    E112237E01
  1. When reinstalling:

    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E150194E01
  1. Place the rear wiper arm and blade assembly so that the rear wiper blade is aligned with the ceramic line.
    Area
    Dimension
    A
    10 mm (0.39 in.)

  1. Install the rear wiper arm and blade assembly with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    HINT:
    Hold down the wiper arm by hand when tightening the nut.



7. INSTALL REAR WIPER ARM HEAD CAP


    E150155
  1. Install the rear wiper arm head cap.

    HINT:
    Push down on the cap until a click sound can be heard.



8. INSTALL REAR WIPER SHAFT COVER
  1. Open the glass hatch.



    E151098
  1. Engage the 3 clips and install the rear wiper shaft cover.

  1. Operate the rear wiper while spraying washer fluid on the glass. Make sure that the rear wiper functions properly and there is no interference with the vehicle body.



9. INSTALL BACK DOOR TRIM PANEL ASSEMBLY


    B174211
  1. Engage the 16 clips and install the back door trim panel assembly.



10. INSTALL ASSIST STRAP ASSEMBLY


    B177264
  1. Install the assist strap assembly with the bolt.



11. INSTALL ASSIST STRAP HOLE COVER


    B177265
  1. Engage the 2 guides and 2 claws, and install the assist strap hole cover.



12. INSTALL BACK DOOR LOCK COVER


    B173203
  1. Engage the 4 guides and 2 claws, and install the back door lock cover.



13. INSTALL BACK DOOR TRIM COVER LH (w/o Power Back Door)


    B173199
  1. Engage the 2 clips and 2 claws, and install the back door trim cover LH.



14. INSTALL BACK DOOR TRIM COVER LH (w/ Power Back Door)


    B173202
  1. Engage the 2 clips and 2 claws, and install the back door trim cover LH.



15. CONNECT POWER BACK DOOR ROD (w/ Power Back Door)


    B173201
  1. Install the back door stay plate and connect the power back door rod.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



16. INSTALL BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)


    B173200
  1. Engage the 6 claws and install the back door service hole cover LH.



17. INSTALL BACK DOOR TRIM COVER RH


    B174214
  1. Engage the 2 clips and 2 claws, and install the back door trim cover RH.



18. INSTALL BACK WINDOW UPPER TRIM PANEL ASSEMBLY


    B173198
  1. Engage the 4 clips and 4 claws, and install the back window upper trim panel assembly.