Home › BODY › WINDSHIELD / WINDOWGLASS › BACK WINDOW LOCK

BACK WINDOW LOCK > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
  1. Be sure to use the centering jig when removing and installing the rear wiper motor assembly (for Glass Hatch Type). Failure to do so will result in a change of the location of the axis of the rear wiper motor assembly (for Glass Hatch Type), causing the wiping angle to change.
  2. After installing the rear wiper motor assembly (for Glass Hatch Type), do not open the glass hatch before installing the rear wiper link pivot.
  3. If the rear wiper motor assembly is removed without using the centering jig, the rear wiper motor assembly must be replaced with a new one.



2. REMOVE BACK WINDOW UPPER TRIM PANEL ASSEMBLY


    B173198
  1. Disengage the 4 clips and 4 claws, and remove the back window upper trim panel assembly.



3. REMOVE BACK DOOR TRIM COVER LH (w/o Power Back Door)


    B173199
  1. Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.



4. REMOVE BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)


    B173200
  1. Disengage the 6 claws, and remove the back door service hole cover LH.



5. DISCONNECT POWER BACK DOOR ROD (w/ Power Back Door)


    B173201
  1. Disconnect the power back door rod and remove the back door stay plate.



6. REMOVE BACK DOOR TRIM COVER LH (w/ Power Back Door)


    B173202
  1. Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.



7. REMOVE BACK DOOR TRIM COVER RH


    B174214
  1. Disengage the 2 clips and 2 claws, and remove the back door trim cover RH.



8. REMOVE BACK DOOR LOCK COVER (for Glass Hatch Type)


    B173203
  1. Disengage the 2 claws and 4 guides, and remove the back door lock cover.



9. REMOVE ASSIST STRAP HOLE COVER


    B177265
  1. Disengage the 2 claws and 2 guides, and remove the assist strap hole cover.



10. REMOVE ASSIST STRAP ASSEMBLY


    B177264
  1. Remove the bolt and assist strap assembly.



11. REMOVE BACK DOOR TRIM PANEL ASSEMBLY


    B174211
  1. Disengage the 16 clips and remove the back door trim panel assembly.



12. REMOVE REAR WIPER SHAFT COVER


    E151098
  1. Disengage the 3 clips and remove the rear wiper shaft cover.



13. REMOVE REAR WIPER ARM HEAD CAP


    E150155
  1. Remove the rear wiper arm head cap.



14. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY


    E150156
  1. Remove the nut and the rear wiper arm and blade assembly.



15. REMOVE REAR WIPER LINK CAP


    E150157
  1. Remove the rear wiper link cap.



16. REMOVE REAR WIPER LINK PIVOT


    E150158
  1. Remove the nut and the rear wiper link pivot.



17. REMOVE REAR WIPER MOTOR ASSEMBLY


  1. When reinstalling the rear wiper motor assembly :

    1. Open the glass hatch.



    2. E154835
    3. Engage the 3 claws and 2 guides, and then install the centering jig.

      NOTICE:
      1. The centering jig cannot be reused.
      2. Do not remove the centering jig before installing the rear wiper link pivot.



    4. E152621
    5. Close the glass hatch, and engage the 2 claws and guide.

      NOTICE:
      Be sure to engage the 2 claws and guide securely.



    6. E151099
    7. Disconnect the connector.

    8. Remove the 2 nuts.

    9. Remove the 4 bolts and the rear wiper motor assembly.

      NOTICE:
      1. Do not hold the rear wiper motor assembly by the rear wiper link pivot.
      2. Be careful not to scratch the back door glass.



  1. When using a new rear wiper motor assembly:



      E150159
    1. Disconnect the connector.

    2. Remove the 4 bolts.



    3. E150183
    4. Remove the 2 nuts and the rear wiper motor assembly.

      NOTICE:
      Be careful not to scratch the back door glass.



18. REMOVE BACK WINDOW LOCK ASSEMBLY


    B173453
  1. Disconnect the connector.

  1. Disengage the clamp.



    B173454
  1. Remove the 3 bolts.



    B173455
  1. Disengage the clip and remove the back window lock assembly.