Home › BODY ELECTRICAL › AUDIO / VISUAL › AMPLIFIER ANTENNA

AMPLIFIER ANTENNA > INSTALLATION

for Preparation Click here



1. INSTALL AMPLIFIER ANTENNA ASSEMBLY


  1. Install the amplifier antenna assembly with the 5 bolts.


    E150572

  1. Engage the 9 clamps.



2. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


    B173274
  1. Pull the roof headlining assembly into the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.

  1. Install the 3 clips.

  1. for Pole Antenna Type with Satellite Radio:

    1. Connect the No. 2 antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

  1. except Pole Antenna Type without Satellite Radio:

    1. Connect the No. 2 antenna cord sub-assembly connector to the rear pillar RH.

  1. except Pole Antenna Type with Satellite Radio:

    1. Connect the No. 2 antenna cord sub-assembly connectors and engage the clamp to the rear pillar RH.

  1. for Pole Antenna Type with Satellite Radio:

    1. Connect the No. 2 antenna cord sub-assembly connector and engage the 2 clamps to the front pillar RH.

  1. except Pole Antenna without Satellite Radio:

    1. Connect the No. 2 antenna cord sub-assembly connector and engage the 3 clamps to the front pillar RH.

    2. Install the No. 2 antenna cord sub-assembly to the front pillar RH with the bolt.

  1. w/ Rear Seat Entertainment System:

    1. Connect the No. 1 roof wire connector to the rear pillar LH.



  1. Connect the No. 1 roof wire connectors and engage the 3 clamps to the front pillar LH.


    B209457E01

    NOTICE:
    After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.



3. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)


    B173271
  1. Pull the roof headlining assembly into the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.

  1. Install the 4 clips.

  1. for Pole Antenna Type with Satellite Radio:

    1. Connect the No. 2 antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

  1. except Pole Antenna Type without Satellite Radio:

    1. Connect the No. 2 antenna cord sub-assembly connector to the rear pillar RH.

  1. except Pole Antenna Type with Satellite Radio:

    1. Connect the No. 2 antenna cord sub-assembly connectors and engage the clamp to the rear pillar RH.

  1. for Pole Antenna Type with Satellite Radio:

    1. Connect the No. 2 antenna cord sub-assembly connector and engage the 2 clamps to the front pillar RH.

  1. except Pole Antenna without Satellite Radio:

    1. Connect the No. 2 antenna cord sub-assembly connector and engage the 3 clamps to the front pillar RH.

    2. Install the No. 2 antenna cord sub-assembly to the front pillar RH with the bolt.



  1. Connect the No. 1 roof wire connector and engage the 3 clamps to the front pillar LH.


    B209458E01

    NOTICE:
    After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.



4. INSTALL VISOR HOLDER


    B151383
  1. Engage the 2 claws.

  1. Push in the visor holder as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and the LH side.



5. INSTALL SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)


    B175148E01
  1. Align the joining point of the moulding with the notch of the roof headlining assembly, and install the sun roof opening trim moulding.

    NOTICE:
    After installation, check that the corners fit correctly.



6. INSTALL ROOF HEADLINING TRIM CLIP STOPPER


    B173594
  1. Install the roof headlining trim clip stopper with the bolt.

  1. Engage the 3 claws.

    HINT:
    Use the same procedure for the RH side and the LH side.



7. INSTALL ASSIST GRIP ASSEMBLY (w/ Sliding Roof)


    B173259
  1. Assemble the assist grip assembly as shown in the illustration.



    B173260
  1. Install the assist grip assembly.

    HINT:
    Use the same procedure for the other 4 assist grips.



8. INSTALL REAR ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)


    B131970
  1. Assemble the rear assist grip sub-assembly as shown in the illustration.



    B167237
  1. Install the rear assist grip sub-assembly.

    HINT:
    Use the same procedure for the RH side and the LH side.



9. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)


    B125984
  1. Assemble the front assist grip sub-assembly as shown in the illustration.



    B160427
  1. Install the front assist grip sub-assembly.

    HINT:
    Use the same procedure for the RH side and the LH side.



10. INSTALL TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)


    E151790
  1. Engage the 2 claws and the 2 clips.



    E150582
  1. Install the television display with the 4 bolts.

  1. Connect the connector.



11. INSTALL TELEVISION BASE (w/ Rear Seat Entertainment System)


    E150581E01
  1. Engage the 2 guides and 4 clips and install the television base.



12. INSTALL NO. 2 ROOM LIGHT ASSEMBLY


    B139564
  1. Engage the 4 claws and install the lens cover.



    B139562
  1. Engage the 4 claws and install the room light switch base to the No. 2 room light assembly.



    B160475
  1. Engage the 4 claws and install the No. 2 room light assembly.



13. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (for Standard)


    B139564
  1. Engage the 4 claws and install the lens cover.



    B139562
  1. Engage the 4 claws and install the room light switch base to the No. 1 room light assembly.



    B160475
  1. Engage the 4 claws and install the No. 1 room light assembly.



14. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (for Independent Type)


    B173253
  1. Engage the 4 claws and install the lens cover.



    B173256
  1. Engage the 8 claws and install the room light switch base to the No. 1 room light assembly.



    B173255
  1. Engage the 4 claws and install the No. 1 room light assembly.



15. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    B175049
  1. Engage the 2 claws and install the inner rear view mirror stay holder cover.



    B175050E01
  1. Engage the 2 claws and install the inner rear view mirror stay holder cover as shown in the illustration.



16. INSTALL VISOR ASSEMBLY LH


    B173261
  1. Install the visor assembly LH with the 2 screws.



17. INSTALL VISOR BRACKET COVER (for LH Side)


    B139566
  1. Engage the 4 claws and install the visor bracket cover.



18. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



19. INSTALL VISOR BRACKET COVER (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.



20. INSTALL ROOF CONSOLE BOX ASSEMBLY


    B173251
  1. Connect the connector.

  1. Engage the 3 guides, 2 clips, fastener, and install the roof console box assembly.



21. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door)


  1. w/ Rear No. 2 Seat:



      B173265
    1. Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.



    3. B175157
    4. Engage the 2 guides and the 2 claws, and install the No. 2 seat outer belt guide.



  1. w/o Rear No. 2 Seat:



      B173266
    1. Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.



22. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door)


  1. w/ Rear No. 2 Seat:



      B173267
    1. Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.



    3. B175157
    4. Engage the 2 guides and the 2 claws, and install the No. 2 seat outer belt guide.



  1. w/o Rear No. 2 Seat:



      B173268
    1. Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.



23. INSTALL QUARTER PILLAR GARNISH LH


    B173264
  1. Engage the 2 guides and the 2 clips, and install the quarter pillar garnish LH as shown in the illustration.



    B175156
  1. Engage the 2 guides and the 2 claws, and install the No. 1 seat outer belt guide.



24. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.



  1. Install the deck trim side panel assembly LH with the 2 bolts.


    B173613



25. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


    B170934E01
  1. Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.



26. INSTALL FRONT DECK SIDE TRIM COVER LH


    B175145
  1. Engage the 4 claws and install the 2 front deck side trim covers LH.



27. INSTALL NO. 2 DECK SIDE TRIM HOOK


    B173612
  1. Install the No. 2 deck side trim hook with the screw.



28. INSTALL ROPE HOOK ASSEMBLY (for LH Side)


    B173599
  1. for Front Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.



    B173601
  1. for Rear Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.



29. INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function)


    B173602
  1. Engage the 10 claws and install the rear deck trim cover.



30. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)


    B173603
  1. Engage the 5 claws and install the reclining remote control bezel LH.



31. INSTALL REAR POWER OUTLET SOCKET COVER


    E151328
  1. Engage the 2 claws and install the rear power outlet socket cover.



32. INSTALL REAR POWER POINT SOCKET ASSEMBLY


    E151490
  1. Engage the claw and install the rear power point socket assembly.

  1. Connect the connector.



33. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH


    B175146
  1. Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.



34. INSTALL SIDE TRIM COVER LH (w/o Rear Seat Entertainment System)


    B173597
  1. Engage the 10 claws and install the side trim cover LH.



35. INSTALL POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System)


    B173681
  1. Connect each connector.



    B173680
  1. Engage the 4 claws and install the power outlet socket bezel.



36. INSTALL DECK SIDE TRIM LH


    B173624
  1. Engage the 3 guides and 4 claws as shown in the illustration.



    B173596
  1. Install the deck side trim LH with the bolt.



37. INSTALL DECK SIDE TRIM COVER LH


    B175144
  1. Engage the 2 claws and install the deck side trim cover LH.



38. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.



39. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.



40. INSTALL QUARTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.



41. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.



  1. Install the deck trim side panel assembly RH with the 3 bolts.


    B173622



42. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



43. INSTALL FRONT DECK SIDE TRIM COVER RH

HINT:
Use the same procedure for the RH side and the LH side.



44. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

HINT:
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.



45. INSTALL ROPE HOOK ASSEMBLY (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.



46. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH


    B173619
  1. Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.



47. INSTALL REAR ROOM TEMPERATURE SENSOR (w/ Rear Automatic Air Conditioning System)
  1. Connect the connector.



    E150364
  1. Engage the 4 claws and install the rear room temperature sensor.



48. INSTALL SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)


    B173610
  1. Engage the 4 claws, and install the side trim cover RH.



49. INSTALL DECK SIDE TRIM RH

HINT:
Use the same procedure for the RH side and the LH side.



50. INSTALL DECK SIDE TRIM COVER RH

HINT:
Use the same procedure for the RH side and the LH side.



51. INSTALL REAR SEAT SIDE GARNISH CAP (w/ Rear Air Conditioning System)


    B173617
  1. Engage the guide and the 6 claws.

  1. Install the rear seat side garnish cap with the screw.



52. INSTALL REAR SEAT SIDE GARNISH CAP (w/o Rear Air Conditioning System)


    B173615
  1. Engage the guide and the 8 claws, and install the rear seat side garnish cap.



53. INSTALL REAR FLOOR FINISH PLATE


    B173609
  1. Engage the 4 clips and the 4 claws, and install the rear floor finish plate.



54. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    B205721
  1. Install the rear No. 2 seat assembly with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



55. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    B170936
  1. Install the rear seat lap type belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.



56. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)
  1. Install the rear seat lap type belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.



57. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    B170935
  1. Install the rear No. 2 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

    HINT:
    Use the same procedure for the RH side and LH side.



58. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    B173679
  1. Install the rear deck floor box with the 2 nuts.



59. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    B178560
  1. Install the rear deck floor board assembly with the 4 nuts and 4 bolts.



60. INSTALL REAR MAT


    B173249
  1. Install the rear mat.



61. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    B178561
  1. Install the 2 nuts and the deck floor board assembly.

  1. Engage the 3 claws.



62. INSTALL DECK SIDE TRIM BOX LH


  1. Install the deck side trim box LH as shown in the illustration.


    B178555



    B173243E01
  1. Install the 2 deck side trim clip and the clips.



63. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    B173607
  1. Engage the 2 clips and install the rear seat side cover LH.



64. INSTALL DECK SIDE TRIM BOX RH


  1. Install the deck side trim box RH as shown in the illustration.


    B178553



    B173247E01
  1. Install the 2 deck side trim clip and the clip.



65. INSTALL JACK CARRIER ASSEMBLY


    B178549
  1. Engage the 3 claws, and install the jack carrier assembly.



66. INSTALL JACK ASSEMBLY


    B173245
  1. Install the jack assembly.



67. INSTALL JACK CARRIER CUSHION


    B178550
  1. Install the jack carrier cushion.



68. INSTALL JACK CARRIER SUPPORT


69. INSTALL REAR SEAT SIDE COVER RH (w/ Rear Air Conditioning System)


    B173608
  1. Engage the 2 clips and install the rear seat side cover RH.



70. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear Air Conditioning System)


    B175152
  1. Engage the 3 guides and 3 clips and install the rear No. 1 floor board.



71. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.



72. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    B173244
  1. Engage the 2 guides and install the No. 2 deck board sub-assembly.



73. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    B173242
  1. Engage the 2 guides and install the No. 3 deck board sub-assembly.



74. INSTALL DECK BOARD ASSEMBLY


    B173240
  1. Install the deck board sub-assembly.



75. INSTALL CENTER PILLAR GARNISH LH


    B173229
  1. Engage the 2 guides and the clip.

  1. Install the center pillar garnish LH with the clip and screw.



76. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B170910
  1. Install the floor end of the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.



77. INSTALL LOWER CENTER PILLAR GARNISH LH


    B173231
  1. Engage the 2 claws and the 2 clips, and install the lower center pillar garnish LH.



78. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B173233E01
  1. Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.



79. INSTALL REAR DOOR SCUFF PLATE LH


    B173228
  1. Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.



80. INSTALL FRONT PILLAR GARNISH LH


    B173226E01
  1. Remove the protective cover.



    B173223E01
  1. Install a new clip <A> on the front pillar garnish LH.

  1. Engage the 3 guides and 2 clips, then install the front pillar garnish LH.



81. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B173235E01
  1. Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.



82. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    B173227
  1. Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.



83. INSTALL FRONT DOOR SCUFF PLATE LH


    B173224
  1. Engage the guide and the 8 claws, and install the front door scuff plate LH.



84. INSTALL CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.



85. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



86. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.



87. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B173237E01
  1. Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

    NOTICE:
    After installation, check that the corners fit correctly.



88. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.



89. INSTALL FRONT PILLAR GARNISH RH


    B173685E01
  1. Remove the protective cover.



    B173683E01
  1. Install a new clip <A> on the front pillar garnish RH.

  1. Engage the 3 guides and 2 clips, then install the front pillar garnish RH.



90. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B173239E01
  1. Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

    NOTICE:
    After installation, check that the corners fit correctly.



91. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



92. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.



93. INSTALL REAR NO. 1 SEAT ASSEMBLY LH


    B173778
  1. Temporarily install the 2 bolts on the front side of the seat.



    B173780
  1. Temporarily install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



94. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)


  1. Remove the rear seat reclining control cable from the carpet hole.


    B180395E01

  1. Connect the rear seat reclining control cable as shown in the illustration.



  1. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.


    B173771E01



    B174591
  1. Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Return the seatback to the upright position.



  1. Pull up the adjuster's lock piece to lock it as shown in the illustration.


    B180389E01

    NOTICE:
    When pressing the lock piece, make sure the adjuster's spring is not compress.



95. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for LH Side)
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.



96. INSTALL REAR SEAT LEG SIDE COVER LH


    B173779
  1. Engage the clip.

  1. Engage the 3 claws and install the rear seat leg side cover.



97. INSTALL REAR INNER TRACK BRACKET COVER LH


    B173777
  1. Engage the 4 claws and install the rear inner track bracket cover.



98. INSTALL REAR OUTER TRACK BRACKET COVER LH


    B173776
  1. Engage the 4 claws and install the rear outer track bracket cover.



99. INSTALL REAR SEAT TRACK BRACKET COVER LH


    B173775
  1. Engage the 8 claws and install the 2 rear seat track bracket covers.



100. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)


    B176351
  1. Install the rear seat headrest assembly as shown in the illustration.



101. INSTALL REAR CENTER SEAT ASSEMBLY


102. INSTALL REAR NO. 1 SEAT ASSEMBLY RH


    B173764
  1. Temporarily install the 2 bolts on the front side of the seat.



    B173774
  1. Temporarily Install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



103. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)


  1. Remove the rear seat reclining control cable from the carpet hole.


    B180394E01

  1. Connect the rear seat reclining control cable as shown in the illustration.



  1. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.


    B173769E01



    B173767
  1. Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Return the seatback to the upright position.



  1. Pull up the adjuster's lock piece to lock it as shown in the illustration.


    B180391E01

    NOTICE:
    When pressing the lock piece, make sure the adjuster's spring is not compress.



104. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for RH Side)
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.



105. INSTALL REAR SEAT LEG SIDE COVER RH


    B173765
  1. Engage the clip.

  1. Engage the 3 claws and install the rear seat leg side cover.



106. INSTALL REAR INNER TRACK BRACKET COVER RH


    B173761
  1. Engage the 4 claws and install the rear inner track bracket cover.



107. INSTALL REAR OUTER TRACK BRACKET COVER RH


    B204931
  1. Engage the 5 claws and install the rear outer track bracket cover.



108. INSTALL REAR SEAT TRACK BRACKET COVER RH


    B173760
  1. Engage the 8 claws and install the 2 seat track bracket covers.



109. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)


    B176352
  1. Install the rear seat headrest assembly as shown in the illustration.