CAMSHAFT (for Bank 2) > REMOVAL |
| 1. REMOVE ENGINE ASSEMBLY |
| 2. INSTALL ENGINE STAND |
| 3. REMOVE IGNITION COIL ASSEMBLY |
![]() |
Remove the 4 bolts [A].
Remove the nut [B].
Disconnect the 2 harness clamps [C].
![]() |
Disconnect the 6 ignition coil connectors.
Remove the 6 bolts and 6 ignition coils.
| 4. REMOVE NO. 2 ENGINE MOUNTING STAY RH |
![]() |
Remove the bolt and No. 2 engine mounting stay RH.
| 5. REMOVE INTAKE MANIFOLD |
![]() |
Uniformly loosen and remove the 6 bolts and 4 nuts.
Remove the intake manifold and 2 gaskets.
| 6. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH |
![]() |
Uniformly loosen and remove the 6 nuts.
Remove the exhaust manifold sub-assembly and gasket.
| 7. REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE |
![]() |
Remove the oil level dipstick.
Remove the bolt and No. 2 engine oil level dipstick guide.
![]() |
Remove the O-rings from the No. 2 engine oil level dipstick guide.
| 8. REMOVE NO. 2 MANIFOLD STAY |
![]() |
Remove the bolt, nut and No. 2 manifold stay.
| 9. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Remove the 3 bolts and No. 2 exhaust manifold heat insulator.
| 10. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH |
![]() |
Uniformly loosen and remove the 6 nuts.
Remove the exhaust manifold assembly and gasket.
| 11. REMOVE TRANSVERSE ENGINE MOUNTING BRACKET |
![]() |
Remove the 3 bolts and transverse engine mounting bracket.
| 12. REMOVE GENERATOR ASSEMBLY |
![]() |
Remove the terminal cap.
Remove the nut and disconnect the wire harness from terminal B.
Disconnect the generator connector from the generator assembly.
Disconnect the connector from the compressor and magnetic clutch.
Disconnect the 3 wire harness clamps.
![]() |
Remove the 2 bolts, and then disconnect the bracket.
![]() |
Remove the 2 bolts and the generator assembly.
![]() |
Disconnect the wire harness clamp, and then remove the generator bracket.
![]() |
Remove the bolt and the wire harness clamp stay.
| 13. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the 5 bolts and V-ribbed belt tensioner assembly.
| 14. REMOVE NO. 2 TIMING GEAR COVER |
![]() |
Remove the 2 bolts and No. 2 timing gear cover.
| 15. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY |
![]() |
Remove the bolt, No. 2 idler pulley cover plate, No. 2 idler pulley sub-assembly and idler pulley cover plate.
| 16. REMOVE NO. 1 ENGINE FRONT MOUNTING BRACKET LH |
![]() |
Remove the 6 bolts and No. 1 engine front mounting bracket LH.
| 17. REMOVE RADIO SETTING CONDENSER |
![]() |
Remove the 2 bolts and 2 radio setting condensers.
| 18. REMOVE NO. 1 VACUUM SWITCHING VALVE |
![]() |
Remove the bolt and No. 1 vacuum switching valve.
| 19. REMOVE KNOCK CONTROL SENSOR WIRE |
![]() |
Disconnect the 2 knock control sensor connectors and 3 clamps, and remove the knock control sensor wire from the engine assembly.
| 20. REMOVE KNOCK CONTROL SENSOR |
![]() |
Disconnect the 2 knock control sensor connectors.
Remove the 2 bolts and then remove the 2 knock control sensors.
| 21. REMOVE CRANKSHAFT POSITION SENSOR |
![]() |
Remove the bolt and crankshaft position sensor.
| 22. REMOVE NO. 1 OIL PIPE |
![]() |
Remove the 2 oil pipe unions, gaskets and No. 1 oil pipe.
Remove the oil control valve filter LH and gaskets.
| 23. REMOVE OIL PIPE |
![]() |
Remove the bolt.
Remove the 2 oil pipe unions and oil pipe.
Remove the oil control valve filter RH and gaskets.
| 24. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, loosen the crankshaft pulley bolt.
![]() |
Using SST, remove the crankshaft pulley bolt and crankshaft pulley.
| 25. REMOVE OIL COOLER ASSEMBLY (w/ Oil Cooler) |
![]() |
Remove the bolt, 2 clamps, and 4 clips and disconnect the 2 water by-pass hoses.
![]() |
Remove the union bolt, oil cooler assembly, and O-ring.
| 26. REMOVE NO. 1 OIL COOLER BRACKET (w/ Oil Cooler) |
![]() |
Remove the 3 bolts, 3 nuts, and oil cooler pipe with No. 1 oil cooler bracket.
![]() |
Remove the bolt, 2 nuts, No. 1 oil cooler bracket, and gasket.
Using a "TORX" socket wrench E8, remove the 2 stud bolts.
| 27. REMOVE WATER INLET HOUSING |
![]() |
Remove the 2 nuts, water inlet and thermostat.
Remove the gasket.
Remove the drain cock plug.
Remove the drain cock assembly.
Remove the 2 stud bolts.
Separate the No. 1 water by-pass hose.
![]() |
Remove the 2 bolts, nut and water inlet housing.
![]() |
Remove the 2 O-rings.
| 28. REMOVE WATER OUTLET |
![]() |
Remove the 2 bolts, 4 nuts and water outlet.
![]() |
Remove the 2 gaskets and O-ring.
| 29. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1) |
![]() |
Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and cylinder head cover gasket.
![]() |
Remove the 3 gaskets.
| 30. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2) |
![]() |
Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and cylinder head cover gasket.
![]() |
Remove the 3 gaskets.
| 31. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 16 bolts and 2 nuts.
![]() |
Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.
Using a "TORX" socket wrench E6, remove the 2 stud bolts.
| 32. REMOVE OIL STRAINER SUB-ASSEMBLY |
![]() |
Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.
Using a "TORX" socket wrench E6, remove the 2 stud bolts.
| 33. REMOVE OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 16 bolts and 2 nuts.
![]() |
Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly with a screwdriver.
![]() |
Remove the 2 O-rings.
Using a "TORX" socket wrench E8, remove the 2 stud bolts.
| 34. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Remove the 15 bolts and 2 nuts as shown in the illustration.
![]() |
Remove the timing chain cover sub-assembly by prying between the timing chain cover and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver.
Remove the 4 bolts, chain cover plate and chain cover plate gasket.
![]() |
Remove the gasket.
| 35. REMOVE TIMING CHAIN CASE OIL SEAL |
![]() |
Using a screwdriver, pry out the timing chain case oil seal.
| 36. SET NO. 1 CYLINDER TO TDC/COMPRESSION |
Temporarily tighten the pulley set bolt.
![]() |
Set the timing mark on the crank angle sensor plate to the RH block bore center line (TDC / compression).
![]() |
Check that the timing marks of the camshaft timing gears are aligned with those of the bearing cap as shown in the illustration.
If not, turn the crankshaft 1 revolution (360°) and align the timing marks as shown in the illustration.
| 37. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
Move the stopper plate downward to set the lock, and insert a pin of 1.27 mm diameter (0.05 in.) into the stopper plate's hole.
![]() |
Remove the 2 bolts and No. 1 chain tensioner assembly.
| 38. REMOVE CHAIN TENSIONER SLIPPER |
Remove the chain tensioner slipper.
| 39. REMOVE CHAIN SUB-ASSEMBLY |
![]() |
Turn the crankshaft counterclockwise 10° to loosen the chain sub-assembly.
Remove the pulley set bolt.
![]() |
Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.
![]() |
Turn the camshaft timing gear assembly on the bank 1 clockwise (approximately 60°) and set it as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.
Remove the chain sub-assembly.
| 40. REMOVE IDLE SPROCKET ASSEMBLY |
![]() |
Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft.
| 41. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2) |
![]() |
While pushing down the No. 3 chain tensioner assembly, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to fix the No. 3 chain tensioner assembly.
![]() |
Using SST to hold the hexagonal portion of each camshaft, loosen the flange bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly LH.
Remove the 2 flange bolts, the camshaft timing gear assembly and the camshaft timing exhaust gear assembly LH together with the No. 2 chain.
| 42. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Remove the bolt and No. 3 chain tensioner assembly.
| 43. REMOVE CAMSHAFT BEARING CAP |
![]() |
Check that the camshafts are positioned as shown in the illustration.
![]() |
Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.
![]() |
Uniformly loosen and remove the 13 bearing cap bolts in several steps and in the sequence shown in the illustration.
Remove the 5 camshaft bearing caps.
| 44. REMOVE NO. 3 CAMSHAFT |
Remove the No. 3 camshaft.
| 45. REMOVE NO. 4 CAMSHAFT |
Remove the No. 4 camshaft.
| 46. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH |
![]() |
Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.
| 47. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
Clamp the camshaft in a vise.
![]() |
Put the camshaft timing gear assembly and camshaft together by aligning the key groove and straight pin.
Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the groove.
Check that there is no clearance between the camshaft timing gear assembly's flange and the camshaft.
![]() |
Tighten the flange bolt with the camshaft timing gear assembly fixed.
Check the lock of the camshaft timing gear assembly.
Clamp the camshaft in a vise, and confirm that the camshaft timing gear assembly locks.
![]() |
Release the lock pin.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Break through the tape on the advance side path and the retard side path on the opposite side of the hole of the advance side path, as shown in the illustration.
![]() |
Apply approximately 200 kPa (2.0 kgf/cm2, 28 psi) of air pressure to the 2 opened paths.
![]() |
Check that the camshaft timing gear assembly revolves in the advance direction when reducing the air pressure applied to the retard side path.
When the camshaft timing gear assembly reaches the most advanced position, release the air pressure first from the retard side path and then from advance side path.
Check for smooth rotation.
Turn the camshaft timing gear assembly within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.
Check the lock in the most retarded position.
Confirm that the camshaft timing gear assembly locks at the most retarded position.
![]() |
Remove the flange bolt and camshaft timing gear assembly.
| 48. INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY LH |
Clamp the camshaft in a vise.
![]() |
Put the camshaft timing exhaust gear assembly LH and camshaft together by aligning the key groove and straight pin.
Lightly press and turn the camshaft timing gear against the camshaft, and press harder after the pin enters the groove.
Check that there is no clearance between the gear's flange and the camshaft.
![]() |
Tighten the flange bolt with the camshaft timing exhaust gear assembly LH fixed.
Check the camshaft timing exhaust gear lock.
Make sure that the camshaft timing exhaust gear assembly LH locks.
![]() |
Release the lock pin.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Break through the tape on the advance side path and the retard side path on the opposite side of the hole of the advance side path, as shown in the illustration.
![]() |
Apply approximately 200 kPa (2.0 kgf/cm2, 28 psi) of air pressure to the 2 opened paths (the advance side path and the retard side path).
![]() |
Make sure that the camshaft timing exhaust gear assembly LH rotates in the retard direction when reducing the air pressure applied to the advance side path.
When the camshaft timing exhaust gear assembly LH moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.
Check for smooth rotation.
Turn the camshaft timing exhaust gear assembly LH within its movable range (18.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear assembly turns smoothly.
Check the lock at the most advanced position.
Make sure that the camshaft timing exhaust gear assembly LH locks at the most advanced position.
![]() |
Remove the flange bolt and camshaft timing exhaust gear assembly LH.