Home › ENGINE › 3MZ-FE EXHAUST › EXHAUST PIPE

EXHAUST PIPE > INSTALLATION

for Preparation Click here



1. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A176011
  1. Install the front exhaust pipe assembly and a new gasket with 2 new nuts.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }



2. INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY


    A176010
  1. Install 2 new gaskets and the front No. 3 exhaust pipe sub-assembly with the 2 bolts and 2 new nuts.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }



3. INSTALL CENTER EXHAUST PIPE ASSEMBLY


  1. Inspect the compression spring.



      A077857
    1. Using a vernier caliper, measure the free length of the compression spring.
      Minimum
      41.5 mm (1.634 in.)

      HINT:
      If the free length is less than the minimum, replace the compression spring.

  1. Fully insert a new gasket to the front No. 3 exhaust pipe sub-assembly.



    A181728E08
  1. Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the front No. 3 exhaust pipe sub-assembly.

    NOTICE:
    1. Be sure to install the gasket in the correct direction.
    2. Do not reuse the gasket.
    3. Do not damage the gasket.
    4. To ensure a proper seal, do not use the exhaust pipe to press the gasket onto the center exhaust pipe assembly.



    A177272
  1. Install the damper with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Connect the center exhaust pipe assembly to the 3 exhaust pipe supports.



    A176009
  1. Tighten the 2 bolts and 2 compression springs.

    Torque:
    48 N*m{ 490 kgf*cm , 35 ft.*lbf }



4. INSTALL TAIL EXHAUST PIPE ASSEMBLY


  1. Inspect the compression spring.



      A077857
    1. Using a vernier caliper, measure the free length of the compression spring.
      Minimum
      40.5 mm (1.594 in.)

      HINT:
      If the free length is less than the minimum, replace the compression spring.

  1. Fully insert a new gasket to the center exhaust pipe assembly.



    A181728E03
  1. Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the center exhaust pipe assembly

    NOTICE:
    1. Be sure to install the gasket in the correct direction.
    2. Do not reuse the gasket.
    3. Do not damage the gasket.
    4. To ensure a proper seal, do not use the tail exhaust pipe assembly to press the gasket onto the tail exhaust pipe assembly.

  1. Connect the tail exhaust pipe assembly to the exhaust pipe support.



    A176008
  1. Tighten the 2 bolts and 2 compression springs.

    Torque:
    48 N*m{ 490 kgf*cm , 35 ft.*lbf }



5. INSTALL OXYGEN SENSOR (for Bank 2)
  1. Temporarily tighten the oxygen sensor to the front exhaust pipe sub-assembly.

    NOTICE:
    Do not damage the oxygen sensor.



    A173495E01
  1. Using SST, fully tighten the oxygen sensor to the front exhaust pipe sub-assembly.

    SST
    09224-00010  

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf } for use without SST
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. Make sure that SST and the wrench are connected in a straight line.

  1. Connect the oxygen sensor connector.



6. INSTALL OXYGEN SENSOR (for Bank 1)
  1. Temporarily tighten the oxygen sensor to the front No. 3 exhaust pipe sub-assembly.

    NOTICE:
    Do not damage the oxygen sensor.



    A173497E01
  1. Using SST, fully tighten the oxygen sensor to the front No. 3 exhaust pipe sub-assembly.

    SST
    09224-00010  

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf } for use without SST
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. Make sure that SST and the wrench are connected in a straight line.

  1. Connect the oxygen sensor connector and clamp.



7. INSPECT FOR EXHAUST GAS LEAK
(Click here)


8. INSTALL NO. 2 ENGINE UNDER COVER
  1. Install the 2 bolts and No. 2 engine under cover.



9. INSTALL NO. 1 ENGINE UNDER COVER


    A173813
  1. Fit the clips and install the No. 2 engine room side cover LH.

    NOTICE:
    1. Be sure to engage the clips securely.
    2. Do not apply excessive force or do not hit the cover to engage the clips. This may cause the cover to break.