Home › ENGINE › 3MZ-FE COOLING › RADIATOR

RADIATOR > INSTALLATION

for Preparation Click here



1. INSTALL LOWER RADIATOR SUPPORT


    A177165
  1. Install the 2 lower radiator supports.



2. INSTALL RADIATOR SUPPORT CUSHION


    A177166
  1. Install the 2 radiator support cushions.



3. INSTALL FAN ASSEMBLY WITH MOTOR


    A176025
  1. Put in the fan assembly with motor to the radiator assembly.

  1. Install the fan assembly with motor with the 3 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }



    A183409
  1. Connect the radiator reserve tank hose to the radiator assembly.



4. INSTALL RADIATOR ASSEMBLY AND FAN ASSEMBLY WITH MOTOR


    A177273
  1. Install the radiator assembly and fan assembly with motor.



5. INSTALL COOLER CONDENSER ASSEMBLY


    A176019
  1. Install the cooler condenser assembly with the 4 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



    A176021
  1. Connect the the 3 water hose clamps to the fan shroud.



6. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY


    A176030E01
  1. Install the upper radiator support sub-assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Install the discharge hose bracket with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Attach the 3 hood lock control cable clamps to the upper radiator support sub-assembly.



7. INSTALL HOOD LOCK SUPPORT SUB-ASSEMBLY


    A175943
  1. Install the hood lock support sub-assembly with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Install the clip and 2 clamps.

  1. Connect the 2 connectors.



8. INSTALL HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch)


    B174197
  1. Apply MP grease to the sliding areas of the lock.



    B174190
  1. Connect the hood lock control cable.



    B174189
  1. Install the hood lock assembly with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B174188
  1. Install the hood lock nut cap.



9. INSTALL HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch)


    B174198
  1. Apply MP grease to the sliding areas of the lock.



    B174194
  1. Connect the hood lock control cable.



    B174193
  1. Install the hood lock assembly with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B174192
  1. Install the hood lock nut cap.



    B174191
  1. Connect the connector.



10. INSTALL RADIATOR GRILLE


    B181114
  1. Engage the 4 guides and 6 claws, and install the radiator grille.



    B181109
  1. Install the 4 clips and 2 bolts.



11. CONNECT COOLING FAN ECU CONNECTOR


    A176020
  1. Connect the 2 cooling fan ECU connectors.

  1. Attach the 7 wire harness clamps to the fan shroud.



12. CONNECT NO. 2 RADIATOR HOSE


    A176031
  1. Connect the No. 2 radiator hose to the radiator.



13. CONNECT NO. 1 RADIATOR HOSE


    A176033
  1. Connect the No. 1 radiator hose to the radiator.



14. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner filter element to the air cleaner case.



    A175875
  1. Install the 2 bolts, 4 clamps and air cleaner cap sub-assembly.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



15. INSTALL COOL AIR INTAKE DUCT SEAL
  1. Install the cool air intake duct seal with the 11 clips.



16. ADD ENGINE COOLANT (for Engine)
  1. Tighten the radiator drain cock plug.

  1. Tighten the cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 9 ft.*lbf }

  1. Loosen the air drain plug.



    A176032E01
  1. Install a vinyl tube to the vent tube located on the air drain plug.

  1. Fill the radiator with engine coolant until the vinyl tube is filled with the coolant.

  1. Tighten the air drain plug.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }

    CAUTION:
    1. Do not use an alcohol type coolant or plain water alone.
    2. The coolant must be mixed with plain water (preferably demineralized water).


    Coolant capacity:

    Condition
    Capacity
    w/ rear heater
    12.8 liters (13.5 US qts, 11.2 lmp.qts)
    w/o rear heater
    10.6 liters (11.2 US qts, 9.3 lmp.qts)

    HINT:
    1. Improper coolants may damage the engine cooling system.
    2. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    3. Use of coolant which includes more than 50% (freezing protection down to -35°C (-31°F)) or 60% (freezing protection down to -50°C (-58°F)) of ethylene-glycol is recommended but not more than 70%.
    4. Observe the coolant level inside the radiator by pressing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add the coolant.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Install the radiator cap securely.

  1. Fill the radiator reservoir tank with coolant.

  1. Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.

    HINT:
    The thermostat opening timing can be confirmed by squeezing the inlet radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (C) through (K) and repeat the operation until the coolant level stays at the full level.

  1. Recheck the coolant level inside the radiator reservoir tank. If it is below the full level, add the coolant.



17. INSPECT FOR COOLANT LEAK (for Engine)

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A176028
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Pump the tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and cylinder head.



18. INSTALL NO. 1 ENGINE UNDER COVER