Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



A103802E35

HINT:
The standard normal voltage between each pair of the ECM (included in the hybrid vehicle control ECU) terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of the terminals, shown in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No (Symbols.)
Wiring Color
Terminal Description
Condition
Specified Condition
D35-1 (BATT) - B3-5 (E1)
R - W-B
Battery (for measuring battery voltage and for ECM memory)
Always
9 to 14 V
A43-3 (+BM) - B3-5 (E1)
L - W-B
Power source of throttle motor
Always
9 to 14 V
D35-9 (IGSW) - B3-5 (E1)
G - W-B
Power switch
Power switch on (IG)
9 to 14 V
A43-2 (+B1) - B3-5 (E1)
GR - W-B
Power source of ECM
Power switch on (IG)
9 to 14 V
A43-1 (+B2) - B3-5 (E1)
Y - W-B
Power source of ECM
Power switch on (IG)
9 to 14 V
B3-16 (OC1+) - B3-15 (OC1-)
LG - B
Camshaft timing oil control valve (OCV) (Intake side (bank 1))
Idling
Pulse generation (see waveform 1)
B3-14 (OC2+) - B3-13 (OC2-)
Y - W
Camshaft timing oil control valve (OCV) (Intake side (bank 2))
Idling
Pulse generation (see waveform 1)
A43-12 (MREL) - B3-5 (E1)
Y - W-B
IGCT relay
Power switch on (IG)
9 to 14 V
B1-18 (VC) - B1-28 (E2)
G - BR
Power source for sensors (specific voltage)
Power switch on (IG)
4.5 to 5.0 V
B1-30 (VG) - B1-29 (EVG)
R - G
Mass air flow meter
Idling, Shift lever position P or N, A/C switch OFF
0.5 to 3.0 V
B1-20 (THA) - B1-28 (E2)
B - BR
Intake air temperature sensor
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
B1-19 (THW) - B1-28 (E2)
G-B - BR
Engine coolant temperature sensor
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
B1-21 (VTA) - B1-28 (E2)
W - BR
Throttle position sensor (for engine control)
Power switch on (IG), Throttle valve fully closed
0.5 to 1.2 V
B1-21 (VTA) - B1-28 (E2)
W - BR
Throttle position sensor (for engine control)
Power switch on (IG), Throttle valve fully open
3.2 to 4.8 V
B1-31 (VTA2) - B1-28 (E2)
O - BR
Throttle position sensor (for sensor malfunction detection)
Power switch on (IG), Accelerator pedal released
2.1 to 3.1 V
B1-31 (VTA2) - B1-28 (E2)
O - BR
Throttle position sensor (for sensor malfunction detection)
Power switch on (IG), Accelerator pedal depressed
4.5 to 5.0 V
A43-25 (VPA) - A43-33 (EP1)
BR - W
Accelerator pedal position sensor (for engine control)
Power switch on (IG), Accelerator pedal released
0.5 to 1.1 V
A43-25 (VPA) - A43-33 (EP1)
BR - W
Accelerator pedal position sensor (for engine control)
Power switch on (IG), Accelerator pedal depressed
2.6 to 4.5 V
A43-26 (VPA2) - A43-32 (EP2)
R - Y
Accelerator pedal position sensor (for sensor malfunctioning detection)
Power switch on (IG), Accelerator pedal released
1.2 to 2.0 V
A43-26 (VPA2) - A43-32 (EP2)
R - Y
Accelerator pedal position sensor (for sensor malfunctioning detection)
Power switch on (IG), Accelerator pedal depressed
3.4 to 5.0 V
A43-24 (VCP1) - A43-32 (EP2)
G - Y
Power source of accelerator pedal position sensor (for VPA)
Power switch on (IG)
4.5 to 5.0 V
A43-31 (VCP2) - A43-32 (EP2)
L - Y
Power source of accelerator pedal position sensor (for VPA2)
Power switch on (IG)
4.5 to 5.0 V
B2-4 (HA1A) - B2-6 (E04)
B2-3 (HA2A) - B2-5 (E05)
R - W-B
W - W-B
A/F sensor heater
Idling
Below 3.0 V
B2-4 (HA1A) - B2-6 (E04)
B2-3 (HA2A) - B2-5 (E05)
R - W-B
W - W-B
A/F sensor heater
Power switch on (IG)
9 to 14 V
B2-22 (A1A+) - B3-5 (E1)
BR - W-B
A/F sensor
Power switch on (IG)
3.3 V*
B2-23 (A2A+) - B3-5 (E1)
P - W-B
A/F sensor
Power switch on (IG)
3.3 V*
B2-30 (A1A-) - B3-5 (E1)
Y - W-B
A/F sensor
Power switch on (IG)
3.0 V*
B2-31 (A2A-) - B3-5 (E1)
L - W-B
A/F sensor
Power switch on (IG)
3.0 V*
D35-21 (HT1B) - B3-5 (E1)
B2-33 (HT2B) - B3-5 (E1)
R - W-B
B - W-B
Heated oxygen sensor heater
Idling
Below 3.0 V
D35-21 (HT1B) - B3-5 (E1)
B2-33 (HT2B) - B3-5 (E1)
R - W-B
B - W-B
Heated oxygen sensor heater
Power switch on (IG)
9 to 14 V
D35-19 (OX1B) - B1-28 (E2)
B2-26 (OX2B) - B1-28 (E2)
B - BR
W - BR
Heated oxygen sensor
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine
Pulse generation (see waveform 2)
B1-1 (#10) - B3-5 (E1)
B1-2 (#20) - B3-5 (E1)
B1-3 (#30) - B3-5 (E1)
B1-4 (#40) - B3-5 (E1)
B1-5 (#50) - B3-5 (E1)
B2-7 (#60) - B3-5 (E1)
L - W-B
R - W-B
G - W-B
W - W-B
Y - W-B
G - W-B
Injector
Power switch on (IG)
9 to 14 V
B1-1 (#10) - B3-5 (E1)
B1-2 (#20) - B3-5 (E1)
B1-3 (#30) - B3-5 (E1)
B1-4 (#40) - B3-5 (E1)
B1-5 (#50) - B3-5 (E1)
B2-7 (#60) - B3-5 (E1)
L - W-B
R - W-B
G - W-B
W - W-B
Y - W-B
G - W-B
Injector
Idling
Pulse generation (see waveform 3)
B2-29 (KNK1) - B2-28 (EKNK)
B - W
Knock sensor
Engine speed maintained at 4000 after warming up engine
Pulse generation (see waveform 4)
B2-21 (KNK2) - B2-20 (EKN2)
R - G
Knock sensor
Engine speed maintained at 4000 after warming up engine
Pulse generation (see waveform 4)
B3-27 (VV1+) - B3-24 (NE-)
B-W - G
Variable valve timing (VVT) sensor (Intake side (bank 1))
Idling
Pulse generation (see waveform 5)
B3-26 (VV2+) - B3-24 (NE-)
L - G
Variable valve timing (VVT) sensor (Intake side (bank 2))
Idling
Pulse generation (see waveform 5)
B3-25 (NE+) - B3-24 (NE-)
R - G
Crankshaft position sensor
Idling
Pulse generation (see waveform 5)
B1-8 (IGT1) - B3-5 (E1)
B1-9 (IGT2) - B3-5 (E1)
B1-10 (IGT3) - B3-5 (E1)
B1-11 (IGT4) - B3-5 (E1)
B1-12 (IGT5) - B3-5 (E1)
B1-13 (IGT6) - B3-5 (E1)
R - W-B
P - W-B
G - W-B
BR - W-B
R - W-B
B - W-B
Ignition coil (ignition signal)
Idling
Pulse generation (see waveform 6)
B1-24 (IGF) - B3-5 (E1)
Y - W-B
Ignition coil (ignition confirmation signal)
Power switch on (IG)
4.5 to 5.0 V
B1-24 (IGF) - B3-5 (E1)
Y - W-B
Ignition coil (ignition confirmation signal)
Idling
Pulse generation (see waveform 6)
B1-17 (PRG) - B3-5 (E1)
G - W-B
Purge VSV
Power switch on (IG)
9 to 14 V
B1-17 (PRG) - B3-5 (E1)
G - W-B
Purge VSV
Idling
Pulse generation (see waveform 7)
D35-24 (SPDI) - B3-5 (E1)
G - W-B
Speed signal from combination meter
Power switch on (IG), Driving wheel slowly rotated
Pulse generation (see waveform 8)
D35-20 (ST2) - B3-5 (E1)
Y - W-B
Starter signal
Power switch on (IG)
9 to 14 V
D35-31 (STP) - B3-5 (E1)
R - W-B
Stop light switch
Brake pedal depressed
7.5 to 14 V
D35-31 (STP) - B3-5 (E1)
R - W-B
Stop light switch
Brake pedal released
Below 1.5 V
D35-25 (ST1-) - B3-5 (E1)
LG - W-B
Stop light switch
(opposite to STP terminal)
Power switch on (IG), Brake pedal depressed
Below 1.5 V
D35-25 (ST1-) - B3-5 (E1)
LG - W-B
Stop light switch
(opposite and STP terminal)
Power switch on (IG), Brake pedal released
7.5 to 14 V
B3-3 (M+) - B3-4 (ME01)
R - W-B
Throttle actuator
Idling with warm engine
Pulse generation (see waveform 9)
B3-2 (M-) - B3-4 (ME01)
L - W-B
Throttle actuator
Idling with warm engine
Pulse generation (see waveform 10)
A43-8 (FC) - B3-5 (E1)
O - W-B
Fuel pump control
Power switch on (IG)
9 to 14 V
A43-8 (FC) - B3-5 (E1)
O - W-B
Fuel pump control
Idling
0 to 3 V
D35-14 (W) - B3-5 (E1)
Y - W-B
MIL
Power switch on (IG)
Below 3.0 V
D35-14 (W) - B3-5 (E1)
Y - W-B
MIL
Idling
9 to 14 V
D35-3 (TC) - B3-5 (E1)
L - W-B
Terminal TC of DLC 3
Power switch on (IG)
9 to 14 V
D36-16 (VPMP) - B3-5 (E1)
Y - W-B
Vent valve (built into canister pump module)
Power switch on (IG)
9 to 14 V
D36-6 (MPMP) - B3-5 (E1)
SB - W-B
Vacuum pump (built into canister pump module)
Vacuum pump OFF
0 to 3 V
D36-6 (MPMP) - B3-5 (E1)
SB - W-B
Vacuum pump (built into canister pump module)
Vacuum pump ON
9 to 14 V
D36-27 (PPMP) - B1-28 (E2)
R - BR
Pressure sensor (built into canister pump module)
Power switch on (IG)
3 to 3.6 V
D36-25 (CANH) - B3-5 (E1)
B - W-B
CAN communication line
Power switch on (IG)
Pulse generation (see waveform 11)
D36-33 (CANL) - B3-5 (E1)
W - W-B
CAN communication line
Power switch on (IG)
Pulse generation (see waveform 12)
D36-35 (PTNK) - B1-28 (E2)
B - BR
Fuel tank pressure sensor
Power switch on (IG)
0.5 to 4.5 V
D36-12 (CCV2) - B3-5 (E1)
GR - W-B
Fuel vapor-containment valve
Close valve ON (Open)
Below 1.0 V
Close valve OFF (Close)
10 to 14 V

HINT:
*: The ECM terminal voltage is constant regardless of the output voltage from the sensor.


WAVEFORM 1
A093229E02
Camshaft timing oil control valve (OCV) 
ECM Terminal Name
Between OC1+ and OC1- or OC2+ and OC2-
Tester Range
5 V/DIV., 1 msec./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 2
A088863E05
Heated oxygen sensor 
ECM Terminal Name
Between OX1B and E2 or OX2B and E2
Tester Range
0.2 V/DIV., 200 msec./DIV.
Condition
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:
In DATA LIST, item O2S B1 S2 shows the ECM input values from the heated oxygen sensor.


WAVEFORM 3
A096732E01
Injector No. 1 (to No. 6) injection signal 
ECM Terminal Name
Between #10 (to #60) and E1
Tester Range
2 V/DIV., 20 msec./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 4
A085286E03
Knock sensor 
ECM Terminal Name
Between KNK1 and EKNK
Between KNK2 and EKN2
Tester Range
0.01 to 10 V/DIV., 0.01 to 10 msec./DIV.
Condition
Engine speed maintained at 4000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine rpm increases.
  2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.


WAVEFORM 5
A031763E02
Crankshaft position sensor and VVT 
ECM Terminal Name
Between NE+ and NE-
Between VV1+ and NE- or VV2+ and NE-
Tester Range
5 V/DIV., 20 msec./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 6
G035664E01
Igniter IGT signal (from ECM to igniter) and igniter IGF signal (from igniter to ECM) 
ECM Terminal Name
Between IGT (1 to 6) and E1
Between IGF and E1
Tester Range
2 V/DIV., 20 msec./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 7
A093230E01
Purge VSV 
ECM Terminal Name
Between PRG and E1
Tester Range
5 V/DIV., 50 msec./DIV.
Condition
Idling

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 8
A093224E05
Vehicle speed signal 
ECM Terminal Name
Between SPDI and E1
Tester Range
2 V/DIV., 20 msec./DIV.
Condition
Power switch on (IG), Driving wheel slowly rotated

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 9
A093274E03
Throttle actuator positive terminal 
ECM Terminal Name
Between M+ and ME01
Tester Range
5 V/DIV., 1 msec./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 10
A093275E03
Throttle actuator negative terminal 
ECM Terminal Name
Between M- and ME01
Tester Range
5 V/DIV., 1 msec./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 11
A086154E05
CAN communication signal 
ECM Terminal Name
Between CANH and E1
Tester Range
1 V/DIV., 10 μsec./DIV.
Condition
Power switch on (IG)

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 12
A086155E35
CAN communication signal 
ECM Terminal Name
Between CANL and E1
Tester Range
1 V/DIV., 10 μsec./DIV.
Condition
Power switch on (IG)

HINT:
The waveform varies depending on the CAN communication signal.