Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > FREEZE FRAME DATA

for Preparation Click here



DESCRIPTION
  1. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

  2. A103809E25
    The Techstream displays freeze frame data recorded at five different points: 1) 3 times before the DTC is set, 2) once when the DTC is set, and 3) once after the DTC is set. The data can be used to simulate the vehicle's condition around the time of the malfunction. The data may be helpful in determining the cause of a malfunction. It may also be helpful in determining whether a DTC is being caused by a temporary malfunction.
  3. The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the Techstream, five separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.

LIST OF FREEZE FRAME DATA

LABEL
(Techstream Display)
Measurement Item/Range
Diagnostic Note
Trouble Code
Freeze DTC
-
Vehicle Speed
Vehicle speed
Speed indicated on speedometer
Engine Speed
Engine speed
-
Calculate Load
Calculate load
Calculated load by ECM (included in the hybrid vehicle control ECU)
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If value is approximately 0.0 g/s:
  1. Mass air flow meter power source circuit open or shorted
  2. VG circuit open or shorted
If value is 271.0 g/s or more:
  1. E2G circuit open
Atmosphere Pressure
Atmospheric pressure
-
Coolant Temp
Engine coolant temperature
If value is -40°C (-40°F), sensor circuit open
If value is 140°C (284°F), sensor circuit shorted
Intake Air
Intake air temperature
If value is -40°C (-40°F), sensor circuit open
If value is 140°C (284°F), sensor circuit shorted
Engine Run Time
Accumulated engine running time
-
Initial Engine Coolant Temp
Initial engine coolant temperature
-
Initial Intake Air Temp
Initial intake air temperature
-
Battery Voltage
Battery voltage
-
Throttle Sensor Volt %
Throttle position
Read value with power switch on (Do not start engine)
Throttle Sensor #2 Volt %
Throttle sensor positioning #2
-
Throttle Sensor Position
Throttle sensor positioning
Read value with power switch on (Do not start engine)
Throttle Motor Duty
Throttle motor
-
Injector (Port)
Injection period of No. 1 cylinder
-
Injection Volume (Cylinder 1)
Injection volume
-
Fuel Pump/Speed Status
Fuel pump/speed status
-
Vacuum Pump
Vacuum pump
ON: Operate
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Evap Purge Flow
Purge flow
-
Purge Density Learn Value
Learning value of purge density
-
EVAP System Vent Valve
EVAP system vent valve
ON: Close
Fuel Filler Opener
Fuel filler opener
ON: Open
Fuel Vapor-Containment Valve
Fuel vapor-containment valve
ON: Open
EVAP Purge VSV
EVAP purge VSV
-
Target Air-Fuel Ratio
Air-fuel ratio
-
AF Lambda B1S1
Fuel trim at A/F sensor
-
AF Lambda B2S1
Fuel trim at A/F sensor
-
AFS Voltage B1S1
A/F sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensors
AFS Voltage B2S1
A/F sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensors
AFS Current B1S1
A/F sensor output current
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output current of sensor
AFS Current B2S1
A/F sensor output current
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output current of sensors
O2S B1S2
Heated oxygen sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensors
O2S B2S2
Heated oxygen sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensors
O2S Impedance B1S2
Sub heated oxygen sensor impedance (bank 1 sensor 2)
-
O2S Impedance B2S2
Sub heated oxygen sensor impedance (bank 2 sensor 2)
-
Short FT #1
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #1
Long-term fuel trim
Overall fuel compensation carried out long-term to compensate for a continual deviation of short-term fuel trim from central value
Total FT #1
Total fuel trim
-
Short FT #2
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #2
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central value
Total FT #2
Total fuel trim
-
Fuel System Status #1
Fuel system status (Bank 1)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
  3. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
  4. OL FAULT: Open loop due to detected system fault
  5. CL FAULT: Closed loop but heated oxygen sensor, which is used for fuel control, malfunctioning
Fuel System Status #2
Fuel system status (Bank 2)
  1. OL (Open Loop ): Has not yet satisfied conditions to go closed loop
  2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
  3. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
  4. OL FAULT: Open loop due to detected system fault
  5. CL FAULT: Closed loop but heated oxygen sensor, which is used for fuel control, malfunctioning
IGN advance
Ignition advance
-
Knock Feedback Value
Feedback value of knocking
-
Knock Correct Learn Value
Correction learning value of knocking
-
EGR Close Lrn. Status
-
-
VVT Control #1
VVT control status (bank 1)
-
VVT Control Status #2
VVT control status (bank 2)
-
VVT Aim Angle #1
VVT aim angle (bank1)
-
VVT Change Angle #1
VVT change angle (bank 1)
-
VVT OCV Duty #1
VVT OCV operation duty (bank 1)
-
VVT Aim Angle #2
VVT aim angle (bank 2)
-
VVT Change Angle #2
VVT change angle (bank 2)
-
VVT OCV Duty #2
VVT OCV operation duty (bank 2)
-
Catalyst Temp B1S1
Catalyst temperature
-
Catalyst Temp B2S1
Catalyst temperature
-
Catalyst Temp B1S2
Catalyst temperature
-
Catalyst Temp B2S2
Catalyst temperature
-
Closed Throttle Position SW
Closed throttle position switch
-
MIL
Distance after DTC is detected
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-
TC and TE1
TC and TE1 terminals of DLC3
-
Ignition Trig. Count
Ignition
-
Cylinder #1 Misfire Count
Cylinder #1 misfire count
Displayed only during idling
Cylinder #2 Misfire Count
Cylinder #2 misfire count
Displayed only during idling
Cylinder #3 Misfire Count
Cylinder #3 misfire count
Displayed only during idling
Cylinder #4 Misfire Count
Cylinder #4 misfire count
Displayed only during idling
Cylinder #5 Misfire Count
Cylinder #5 misfire count
Displayed only during idling
Cylinder #6 Misfire Count
Cylinder #6 misfire count
Displayed only during idling
All Cylinder Misfire Count
All cylinder misfire count
Displayed only during idling
Misfire RPM
Misfire RPM
-
Misfire Load
Misfired load
-
Misfire Margin
Misfire monitoring
-
Electric Fan Motor
Electric fan motor
ON: Operate
Requested Engine Torque
Requested engine torque
-
HV Target Engine Speed
HV target engine speed
-
Actual Engine Torque
Actual engine torque
-
Estimated Engine Torque
Estimated engine torque
-
Engine Run Time
Engine run time
-
Requested Engine Run Time
Request engine run time
-
Judge Time Engine Ignition
Judge time engine ignition
-
Judge Time Engine Output
Judge time engine output
-
Fuel Level
Fuel level
-
ISC Learning
ISC learning
-
F/C for Engine Stop Req
Fuel cut for engine stop request
-
Engine Independent
Engine independent operation
-
Racing Operation
Racing operation
-
Request Warm-up
Request warm-up
-
Engine Independent Control
Engine independent control
-
ISC Learning Value
ISC learning control
-