Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0101    Mass Air Flow Circuit Range / Performance Problem

for Preparation Click here


DESCRIPTION

The Mass Air Flow meter is a sensor that measures the amount of air flowing through the valve.
The ECM (included in the hybrid vehicle control ECU) uses this information to determine the fuel injection duration and to provide an appropriate air fuel ratio.
Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air.
By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the mass air flow meter. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor provide a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:
When any of these DTCs are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine RPM and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A140749E02


DTC No.
DTC Detection Condition
Trouble Area
P0101
  1. Conditions (a), (b), (c), (d) and (e) continue for more than 10 seconds (2 trip detection logic):
    1. (a) Time after engine start is 5 seconds or more
    2. (b) Engine coolant temperature 70°C (158°F) or higher
    3. (c) Throttle position sensor voltage 0.2 to 2 V
    4. (d) Average engine load value ratio less than 0.81, or more than 1.17 (varies with estimated engine load)
      Average engine load value ratio = Average engine load based on mass air flow meter output / Average engine load estimated from driving conditions
    5. (e) Average air-fuel ratio less than -20%, or more than 20%
  1. Mass air flow meter
  2. Intake system
  3. PCV hose connections

MONITOR DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve. The ECM (included in the hybrid vehicle control ECU) uses this information to determine the fuel injection duration and to provide an appropriate air-fuel ratio. Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air. By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components of the mass air flow meter. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume. If there is a defect in the sensor, or an open or short in the circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter and sets the DTC.
Example:
If the voltage is more than 2.2 V, or less than 1.48 V while idling, the ECM determines that there is a malfunction in the mass air flow meter and sets the DTC.

MONITOR STRATEGY


Related DTCs
P0101: Mass air flow meter rationality
Required Sensors/Components (Main)
Mass air flow meter
Required Sensors/Components (Related)
Crankshaft position sensor, engine coolant temperature sensor and throttle position sensor
Frequency of Operation
Continuous
Duration
10 times
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
Throttle position (TP sensor voltage)
0.2 to 2 V
Time after engine start
5 seconds or more
Battery voltage
10.5 V or more
Engine coolant temperature
70°C (158°F) or more
Intake air temperature sensor circuit
OK
Engine coolant temperature sensor circuit
OK
Crankshaft position sensor circuit
OK
Throttle position sensor circuit
OK
Canister pressure sensor circuit
OK
EVAP leak detection pump
OK
EVAP vent valve
OK

TYPICAL MALFUNCTION THRESHOLDS


Average engine load
Less than 0.81, or more than 1.15

WIRING DIAGRAM

Refer to DTC P0102 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0101)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch to on (IG).

  1. Turn the Techstream on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0101
    A
    P0101 and other DTCs
    B

HINT:
If any DTCs other than P0101 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks in intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


3.CHECK PCV HOSE CONNECTIONS

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK

REPLACE MASS AIR FLOW METER (Click here)