Home › SUSPENSION & AXLE › AXLE › STEERING KNUCKLE

STEERING KNUCKLE > REMOVAL

for Preparation Click here



1. REMOVE FRONT WHEEL


2. REMOVE FRONT AXLE HUB NUT


    C167528E01
  1. Using SST and a hammer, release the staked part of the front axle shaft nut LH.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle shaft nut LH.



3. SEPARATE FRONT SPEED SENSOR


    C165818E03
  1. Remove the bolt and resin clamp, and separate the front speed sensor.



4. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY


    C165913
  1. Remove the 2 bolts and separate the front disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the front disc brake caliper assembly from hanging down by the flexible hose.



5. REMOVE FRONT DISC


    C165879E01
  1. Remove the front disc.

    HINT:
    Put matchmarks on the disc and the axle hub.



6. SEPARATE TIE ROD ASSEMBLY
  1. Remove the cotter pin and the nut.



    C165542E01
  1. Install SST to the tie rod end.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure that the upper ends of the tie rod end and SST are aligned.



  1. Using SST, separate the tie rod end from the steering knuckle.


    C165543E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. When securing SST to the steering knuckle, be sure to tighten the string of SST to prevent it from falling.
    1. Install SST so that A and B are parallel.
    1. Be sure to place the wrench on the part indicated in the illustration.
    1. Do not damage the front disc brake dust cover.
    1. Do not damage the ball joint dust cover.
    1. Do not damage the steering knuckle.



7. SEPARATE FRONT LOWER SUSPENSION ARM


    C165929
  1. Remove the bolt and 2 nuts, and separate the front lower suspension arm from the front lower ball joint.



8. SEPARATE FRONT DRIVE SHAFT ASSEMBLY


    C165537E05
  1. Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.



    C165534
  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Be careful not to damage the drive shaft boot and speed sensor rotor.



9. REMOVE FRONT AXLE ASSEMBLY


    C166269E01
  1. Remove the 2 bolts, 2 nuts and front axle assembly.

    NOTICE:
    When removing the nuts, keep the bolts from rotating.



10. REMOVE FRONT LOWER BALL JOINT


    C167239
  1. Secure the front axle assembly in a vise using aluminum plates.

    NOTICE:
    When using a vise, do not overtighten it.



    C165931
  1. Remove the cotter pin and nut.



    C165932E02
  1. Install SST to the front lower ball joint as shown in the illustration.

    SST
    09960-20010   (09961-02050, 09961-02050)

    NOTICE:
    Check that the clearance between SST and the front axle assembly is 1 mm (0.04 in.).



    C165933E02
  1. Using SST, remove the front lower ball joint from the front axle assembly as shown in the illustration.

    SST
    09960-20010   (09961-02010, 09961-02050, 09961-02050)

    NOTICE:
    1. Install SST so that A and B are parallel.
    2. Be sure to place a wrench on the part indicated in the illustration.
    3. Do not damage the front lower ball joint dust cover.



11. REMOVE NO. 1 FRONT WHEEL BEARING DUST DEFLECTOR


    C166271E02
  1. Using a screwdriver with its tip wrapped with vinyl tape, remove the No. 1 front wheel bearing dust deflector.

    NOTICE:
    Be careful not to damage the steering knuckle.



12. REMOVE FRONT AXLE HUB HOLE SNAP RING


    C166270
  1. Using snap ring pliers, remove the front axle hub hole snap ring.



13. REMOVE FRONT AXLE HUB SUB-ASSEMBLY
  1. Hold the front axle assembly between aluminium plates in a vise.

    NOTICE:
    Do not overtighten the vise.



    C166272E01
  1. Using SST, remove the front axle hub sub-assembly.

    SST
    09520-00031  



    C167711E02
  1. Using SST and a press, remove the bearing inner race (outside) from the front axle hub sub-assembly.

    SST
    09555-55010  
    09950-60010   (09951-00430)
    09950-70010   (09951-07100)

    NOTICE:
    Be careful not to drop the front axle hub sub-assembly.



14. REMOVE FRONT DISC BRAKE DUST COVER


    C166273
  1. Remove the 4 bolts and front disc brake dust cover from the steering knuckle.



15. REMOVE STEERING KNUCKLE
  1. Place the bearing inner race (outside) on the front axle hub bearing.



    C168043E01
  1. Using SST, V-blocks and a press, remove the front axle hub bearing from the steering knuckle.

    SST
    09950-60010   (09951-00430, 09952-06010)
    09950-70010   (09951-07100)
    09950-60020   (09951-00750)

    NOTICE:
    Keep the steering knuckle level.