Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK POWER SWITCH


  1. Disconnect the D25 power switch connector.


    B146454E04

  2. Measure the resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D25-8 (AGND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D25 power switch connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D25-8 (AGND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    D25-9 (TXCT) - D25-8 (AGND)
    O - V
    Key code output signal
    Key is not in cabin
    Below 1 V
    D25-9 (TXCT) - D25-8 (AGND)
    O - V
    Key code output signal
    Power switch pressed and key is held close to power switch*
    Pulse generation
    (See waveform 1)
    D25-10 (CODE) - D25-8 (AGND)
    GR - V
    Demodulated signal of key code data
    Key is not in cabin
    Below 1 V
    D25-10 (CODE) - D25-8 (AGND)
    GR - V
    Demodulated signal of key code data
    Power switch pressed and key is held close to power switch*
    Pulse generation
    (see waveform 2)
    D25-14 (VC5) - D25-8 (AGND)
    G - V
    Power supply
    Key is not in cabin
    Below 1 V
    D25-14 (VC5) - D25-8 (AGND)
    G - V
    Power supply
    Power switch pressed
    4.6 to 5.4 V

    HINT:
    *: Remove the key battery before performing this inspection.

    1. If the result is not as specified, the power switch may have a malfunction.



  5. Inspect using an oscilloscope.



      B164407E01
    1. Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D25-9 (TXCT) - D25-8 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      Power switch pressed and key is held close to power switch*

      HINT:
      *: Remove the key battery before performing this inspection.



    2. B164408E01
    3. Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D25-10 (CODE) - D25-8 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      Power switch pressed and key is held close to power switch*

      HINT:
      *: Remove the key battery before performing this inspection.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


  1. Disconnect the D40 certification ECU (smart key ECU assembly) connector.


    B178888E01

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D40-1 (+B) - D40-17 (E)
    B - B
    +B power supply
    Always
    11 to 14 V
    D40-17 (E) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    D40-18 (IG) - D40-17 (E)
    G - B
    Ignition power supply
    Power switch off
    Below 1 V
    D40-18 (IG) - D40-17 (E)
    G - B
    Ignition power supply
    Power switch on (IG)
    11 to 14 V

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D40 certification ECU (smart key ECU assembly) connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D40-8 (TXCT) - D40-40 (AGND)
    O - V
    Power switch TXCT output
    Key is not in cabin
    Below 1 V
    D40-8 (TXCT) - D40-40 (AGND)
    O - V
    Power switch TXCT output
    Power switch pressed and key is held close to power switch*
    Pulse generation (See waveform 1)
    D40-9 (CODE) - D40-40 (AGND)
    GR - V
    Power switch CODE input
    Key is not in cabin
    Below 1 V
    D40-9 (CODE) - D40-40 (AGND)
    GR - V
    Power switch CODE input
    Power switch pressed and key is held close to power switch*
    Pulse generation (See waveform 2)
    D40-30 (VC5) - D40-40 (AGND)
    G - V
    Power switch power supply
    Key is not in cabin
    Below 1 V
    D40-30 (VC5) - D40-40 (AGND)
    G - V
    Power switch power supply
    Power switch pressed
    4.6 to 5.4 V
    D40-40 (AGND) - Body ground
    V - Body ground
    Power switch ground
    Always
    Below 1 Ω

    HINT:
    *: Remove the key battery before performing this inspection.

    1. If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.



  5. Inspect using an oscilloscope.



      B164407E01
    1. Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D40-8 (TXCT) - D40-40 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      Power switch pressed and key is held close to power switch*

      HINT:
      *: Remove the key battery before performing this inspection.



    2. B164408E01
    3. Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D40-9 (CODE) - D40-40 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      Power switch pressed and key is held close to power switch*

      HINT:
      *: Remove the key battery before performing this inspection.


CHECK ID CODE BOX (IMMOBILISER CODE ECU)


  1. Disconnect the D31 ID code box (immobiliser code ECU) connector.


    B118534E07

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D31-1 (+B) - D31-8 (GND)
    W - V
    +B power supply
    Always
    11 to 14 V
    D31-8 (GND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D31 ID code box (immobiliser code ECU) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D31-5 (EFII) - D31-8 (GND)
    BR - V
    Hybrid vehicle control ECU input signal
    Power switch off
    Below 1 V
    D31-5 (EFII) - D31-8 (GND)
    BR - V
    Hybrid vehicle control ECU input signal
    Power switch on (IG)
    Pulse generation
    (see waveform 1)
    D31-6 (EFIO) - D31-8 (GND)
    L - V
    Hybrid vehicle control ECU output signal
    Power switch off
    Below 1 V
    D31-6 (EFIO) - D31-8 (GND)
    L - V
    Hybrid vehicle control ECU output signal
    Power switch on (IG)
    Pulse generation
    (see waveform 2)

    1. If the result is not as specified, the ID code box (immobiliser code ECU) may have a malfunction.



  5. Inspect using an oscilloscope.



      B111837E03
    1. Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D31-5 (EFII) - D31-8 (GND)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Condition
      Power switch on (IG)



    2. B111838E03
    3. Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D31-6 (EFIO) - D31-8 (GND)
      Tool Setting
      2 V/DIV., 1 ms./DIV.
      Condition
      Power switch on (IG)


CHECK STEERING LOCK ECU


  1. Disconnect the D11 steering lock ECU connector.


    B118684E09

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D11-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    D11-2 (SGND) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω
    D11-6 (IG2) - Body ground
    V - Body ground
    Ignition power supply
    Power switch off
    Below 1 V
    D11-6 (IG2) - Body ground
    V - Body ground
    Ignition power supply
    Power switch on (IG)
    11 to 14 V
    D11-7 (B) - Body ground
    G - Body ground
    +B power supply
    Always
    11 to 14 V

    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK HYBRID VEHICLE CONTROL ECU


  1. Disconnect the B3 hybrid vehicle control ECU connector and measure the resistance according to the value(s) in the table below.


    A103802E35


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B3-5 (E1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the B3 hybrid vehicle control ECU connector. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D35-28 (IMO) - B3-5 (E1)
    BR - W-B
    Transponder key ECU output signal
    Power switch off
    Below 1 V
    D35-28 (IMO) - B3-5 (E1)
    BR - W-B
    Transponder key ECU output signal
    Power switch on (IG)
    Waveform 1
    D35-22 (IMI) - B3-5 (E1)
    L - W-B
    Transponder key ECU input signal
    Power switch off
    Below 1 V
    D35-22 (IMI) - B3-5 (E1)
    L - W-B
    Transponder key ECU input signal
    Power switch on (IG)
    Waveform 2
    If the result is not as specified, the hybrid vehicle control ECU may have a malfunction.



  3. Inspect using an oscilloscope.



      B111837E03
    1. Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D35-28 (IMO) - B3-5 (E1)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Condition
      Power switch on (IG)



    2. B111838E03
    3. Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D35-22 (IMI) - B3-5 (E1)
      Tool Setting
      2 V/DIV., 1 ms./DIV.
      Condition
      Power switch on (IG)


CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
  1. Disconnect the 1M and 1F junction block connectors.



  2. Disconnect the D7, D8 and D9 main body ECU (instrument panel junction block) connectors.


    B112605E16

  3. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D7-1 (AM2) - Body ground
    B - Body ground
    +B power supply
    Always
    11 to 14 V
    D8-6 (AM1) - Body ground
    GR - Body ground
    +B power supply
    Always
    11 to 14 V
    D9-1 (GND3) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.