Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0441    Evaporative Emission Control System Incorrect Purge Flow

for Preparation Click here


DTC SUMMARY


DTC No.
Monitoring Item
DTC Detection Condition
Trouble Area
Detection Timing
Detection Logic
P0441
Purge VSV (Vacuum Switching Valve) stuck open
Vacuum pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured. 0.02 inch leak pressure standard is measured at the start and at the end of leak check.
If stabilized pressure is higher than [second 0.02 inch leak pressure standard x 0.2], ECM (Included in hybrid vehicle control ECU) determines that Purge VSV stuck open.
  1. Purge VSV
  2. Connector/wire harness
    (Purge VSV - Hybrid vehicle control ECU)
  3. Hybrid vehicle control ECU
  4. Canister pump module
  5. Leakage from EVAP system
Power switch off
2 trip
P0441
Purge VSV stuck closed
After EVAP leak check is performed, Purge VSV turned ON (open), and atmospheric air is introduced into EVAP system. 0.02 inch leak pressure standard is measured at the start and at the end of the check.
If pressure does not return to near atmospheric pressure, ECM (Included in hybrid vehicle control ECU) determines that purge valve stuck closed.
  1. Purge VSV
  2. Connector/wire harness
    (Purge VSV - Hybrid vehicle control ECU)
  3. Hybrid vehicle control ECU
  4. Canister pump module
  5. Leakage from EVAP system
Power switch off
2 trip
P0441
Purge flow
While engine running, the following conditions are successively met:
  1. Negative pressure is not created in EVAP system when Purge VSV turned ON (open)
  2. EVAP system pressure change is less than 0.5 kPa (3.75 mmHg) when vent valve turned ON (closed)
  3. Atmospheric pressure change between before and after purge flow monitor is less than 0.1 kPa (0.75 mmHg)
  1. Purge VSV
  2. Connector/wire harness
    (Purge VSV - Hybrid vehicle control ECU)
  3. Leakage from EVAP line
    (Purge VSV - Intake manifold)
  4. Hybrid vehicle control ECU
Engine running
2 trip

DESCRIPTION

Refer to EVAP System .

MONITOR DESCRIPTION

The two monitors, Key-Off and Purge Flow, are used to detect malfunctions relating to DTC P0441. The Key-Off monitor is initiated by the ECM (included in the hybrid vehicle control ECU) internal timer, known as the soak timer, 5 hours* after the power switch is turned off. The purge flow monitor runs while the engine is running.

KEY-OFF MONITOR
  1. Purge VSV stuck open
    In operation C, the vacuum pump creates negative pressure (vacuum) in the EVAP (Evaporative Emission) system. The EVAP system pressure is then measured by the ECM (included in the hybrid vehicle control ECU) using the pressure sensor. If the stabilized system pressure is higher than [second 0.02 inch leak pressure standard x 0.2], the ECM (included in the hybrid vehicle control ECU) interprets this as the Purge VSV (Vacuum Switching Valve) being stuck open. The ECM illuminates the MIL and sets the DTC (2 trip detection logic).



  2. Purge VSV stuck closed
    In operation D, the pressure sensor measures the EVAP (Evaporative Emission) system pressure. The pressure measurement for Purge VSV monitor begins when the Purge VSV is turned ON (open) after the EVAP leak check. When the measured pressure indicates an increase of 0.3 kPa (2.25 mmHg) or more, the Purge VSV is functioning normally. If the pressure does not increase, the ECM (included in the hybrid vehicle control ECU) interprets this as the Purge VSV being stuck closed. The ECM illuminates the MIL and sets the DTC (2 trip detection logic).


    A109161E05


PURGE FLOW MONITOR


    A071563E19
  1. The purge flow monitor consists of the two step monitors. The 1st monitor is conducted every time and the 2nd monitor is activated if necessary.

    1. The 1st monitor
      While the engine is running and the Purge VSV (Vacuum Switching Valve) is ON (open), the ECM (included in the hybrid vehicle control ECU) monitors the purge flow by measuring the EVAP pressure change. If negative pressure is not created, the ECM begins the 2nd monitor.
    2. The 2nd monitor
      The vent valve is turned ON (closed) and the EVAP pressure is then measured. If the variation in the pressure is less than 0.5 kPa (3.75 mmHg), the ECM (included in the hybrid vehicle control ECU) interprets this as the Purge VSV being stuck closed. The ECM illuminates the MIL and sets DTC P0441 (2 trip detection logic).
    Atmospheric pressure check:
    In order to ensure reliable malfunction detection, the variation in atmospheric pressure, before and after conducting of the purge flow monitor is measured by the ECM.


MONITOR STRATEGY


Required Sensors/Components
Purge VSV and canister pump module
Frequency of Operation
Once per driving cycle
Duration
Within 10 minutes
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs are not present
None

Purge flow: 
Engine
Running
Engine coolant temperature
4.4°C (40°F) or more
Intake air temperature
4.4°C (40°F) or more
EVAP pressure sensor malfunction
Not detected
EVAP canister purge valve
Not operated by scan tool
EVAP system check
Not detected by scan tool
Battery voltage
10 V or more
Purge duty cycle
8% or more

Purge VSV stuck open and closed: 
Key-off monitor is run when all of the following conditions are met:
-
Atmospheric pressure
70 to 110 kPa (525 to 825 mmHg)
Battery voltage
10.5 V or more
Vehicle speed
2.5 mph (4 km/h) or less
Power switch
OFF
Engine condition
Not running
Key-off duration
5 hours or 7 hours or 9 hours and 30 minutes
Pressure sensor of canister pump module malfunction
(P1450, P1452, P1453)
Not detected
Purge VSV
Not operated by scan tool
Vent valve
Not operated by scan tool
Leak detection pump
Not operated by scan tool
Both of the following conditions (a) and (b) are met before power switch off:

(a) Duration that vehicle is being driven
5 minutes or more
(b) Purge flow
Performed
Engine coolant temperature
4.4 to 35°C (40 to 95°F)
Intake air temperature
4.4 to 35°C (40 to 95°F)
  1. Key-off monitor sequence 1 to 15

    1. Atmospheric pressure measurement 
    Next sequence is run if the following condition is met:
    -
    Atmospheric pressure change for 10 seconds
    Less than 0.3 kPa (2.25 mmHg) for 1 second

    2. First reference pressure measurement 
    Next sequence is run if all of the following conditions are met:
    Conditions 1, 2 and 3
    1. EVAP pressure 1.9 seconds after reference pressure measurement
    -1 kPa (-7.5 mmHg) or less
    2. Reference pressure
    -4.85 to -1.057 kPa (-36.4 to -7.93 mmHg)
    3. Reference pressure
    Saturated within 55 seconds

    3. Vent valve stuck closed check 
    Next sequence is run if the following condition is met:
    -
    EVAP pressure change for 10 seconds after vent valve ON (Closed)
    0.3 kPa (2.25 mmHg) or more

    4. Vacuum introduction for canister 
    Next sequence is run if both of the following conditions are met:
    Conditions 1 and 2
    1. Vacuum introduction time
    15 minutes or less
    2. FTP
    Saturated

    5. Purge VSV stuck closed check 
    Next sequence is run if the following condition is met:
    -
    EVAP pressure change for 10 seconds after Purge VSV ON (Open).
    0.3 kPa (2.25 mmHg) or more

    6. Second reference pressure measurement 
    Next sequence is run if all of the following conditions are met:
    Conditions 1, 2, 3 and 4
    1. EVAP pressure 1.9 seconds after reference pressure measurement
    -1 kPa (-7.5 mmHg) or less
    2. Reference pressure
    -4.85 to -1.057 kPa (-36.4 to -7.93 mmHg)
    3. Reference pressure
    Saturated within 55 seconds
    4. Reference pressure difference between the first and second
    0.7 kPa (5.25 mmHg) or less

    7. Canister leak 
    Next sequence is run if the following condition is met:
    -
    Canister leak when vacuum introduction was complete
    Less than second reference pressure

    8. Fuel vapor-containment valve (FVCV stuck closed check) 
    Sequence 14 is run if all of the following conditions are met:
    Conditions 1 and 2
    1. FTP when EVAP monitor started
    -2 kPa (-15 mmHg) or less, or 3 kPa (22.5 mmHg) or more
    2. FTP change while FVCV and vent valve are open
    0.5 kPa (3.75 mmHg) or more

    9. Vacuum introduction for fuel tank 
    Next sequence is run if both of the following conditions are met:
    Conditions 1 and 2
    1. FTP when EVAP monitor started
    -2 to 3 kPa (-15 to 22.5 mmHg)
    2. Vacuum introduction time
    15 minutes or less

    10. FVCV stuck closed check 
    Next sequence is run if the following condition is met:
    -
    FTP change when vacuum introduction for fuel tank
    0.5 kPa (3.75 mmHg)

    11. FTP sensor stuck check 
    Next sequence is run if the following condition is met:
    -
    FTP change when FVCV closed
    0.35 kPa (2.6 mmHg) or less

    12 Third reference pressure measurement 
    Next sequence is run if all of the following conditions are met:
    Conditions 1, 2, 3, and 4
    1. FTP 1.9 seconds after reference pressure measurement
    -1 kPa (-7.5 mmHg) or more
    2. Reference pressure
    -4.85 to -1.057 kPa (-36.4 to -7.93 mmHg)
    3. Reference pressure
    Saturated
    4. Reference pressure difference between the second and third measurement
    Less than 0.7 kPa (5.25 mmHg)

    13. Fuel tank leak check 
    Sequence is run if the following condition is met:
    -
    FTP when vacuum introduction for fuel tank was complete
    Less than third reference pressure

    14. FTP sensor stuck check 
    Next sequence is run if the following condition is met:
    -
    FTP change while FVCV and vent valve are open
    Less than 0.3 kPa (2.25 mmHg)

    15. Atmospheric pressure measurement 
    Monitor is complete if the following condition is met:
    -
    Atmospheric pressure difference between sequences 1 and 8
    0.3 kPa (2.25 mmHg) or less

TYPICAL MALFUNCTION THRESHOLDS


Purge VSV stuck open: 
EVAP pressure when vacuum introduction is complete
Higher than reference pressure x 0.2

Purge VSV stuck closed: 
EVAP pressure chance after EVAP canister purge valve is open
Less than 0.3 kPa (2.25 mmHg)

Purge flow: 
Both of the following conditions are met:
Conditions (a) and (b)
(a) EVAP pressure change when purge operation is started
Less than 0.1 kPa (0.75 mmHg)
(b) EVAP pressure change during purge operation when vent valve is closed
Less than 0.5 kPa (3.75 mmHg)

MONITOR RESULT

Refer to EVAP System .

INSPECTION PROCEDURE

Refer to EVAP System .