Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0451    Evaporative Emission Control System Pressure Sensor Range / Performance

DTC    P0452    Evaporative Emission Control System Pressure Sensor / Switch Low Input

DTC    P0453    Evaporative Emission Control System Pressure Sensor / Switch High Input

for Preparation Click here


DTC SUMMARY


DTC No.
Monitoring Item
DTC Detection Condition
Trouble Area
Detection Timing
Detection Logic
P0451
Pressure sensor abnormal voltage fluctuation
EVAP pressure fluctuates frequently in certain time period.
  1. Canister pump module
  2. Connector/wire harness (Canister pump module - Hybrid vehicle control ECU)
  3. Hybrid vehicle control ECU
  1. EVAP monitoring (power switch off)
  2. Power switch on
2 trips
P0451
Pressure sensor constant voltage
EVAP pressure does not vary in certain time period.
  1. Canister pump module
  2. Connector/wire harness (Canister pump module - Hybrid vehicle control ECU)
  3. Hybrid vehicle control ECU
EVAP monitoring (power switch off)
2 trips
P0452
Pressure sensor voltage low
EVAP pressure is less than 42.11 kPa (315.82 mmHg) for 0.5 seconds.
  1. Canister pump module
  2. Connector/wire harness (Canister pump module - Hybrid vehicle control ECU)
  3. Hybrid vehicle control ECU
  1. EVAP monitoring (power switch off)
  2. Power switch on
1 trip
P0453
Pressure sensor voltage high
EVAP pressure is more than 123.761 kPa (928.207 mmHg) for 0.5 seconds.
  1. Canister pump module
  2. Connector/wire harness (Canister pump module - Hybrid vehicle control ECU)
  3. Hybrid vehicle control ECU
  1. EVAP monitoring (power switch off)
  2. Power switch on
1 trip

HINT:
The pressure sensor is built into the canister pump module.


DESCRIPTION

Refer to EVAP System .

MONITOR DESCRIPTION

  1. DTC P0451: Pressure sensor abnormal voltage fluctuation or being constant
    If the pressure sensor output voltage fluctuates rapidly for 10 seconds, the ECM (included in the hybrid vehicle control ECU) stops the EVAP system monitor. The ECM interprets this as the pressure sensor voltage fluctuating, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC.
    Alternatively, if the sensor output voltage does not change for 10 seconds, the ECM interprets this as the sensor voltage being constant, and stops the monitor. The ECM then illuminates the MIL and sets the DTC.
    (Both the malfunctions are detected by 2 trip detection logic).
  2. DTC P0452: Pressure sensor voltage low
    If the pressure sensor output voltage is below 0.45 V, the ECM (included in the hybrid vehicle control ECU) interprets this as an open or short circuit in the pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC (1 trip detection logic).
  3. DTC P0453: Pressure sensor voltage high
    If the pressure sensor voltage output is 4.9 V or more, the ECM (included in the hybrid vehicle control ECU) interprets this as an open or short circuit in the pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC (1 trip detection logic).

MONITOR STRATEGY


Required Sensors/Components
Canister pump module
Frequency of Operation
Once per driving cycle: P0451 sensor constant voltage
Continuous: P0451 sensor abnormal voltage fluctuation, P0452 and P0453
Duration
0.5 seconds: P0452, P0453
Less than 15 seconds: P0451
MIL Operation
Immediate: P0452, P0453
2 driving cycles: P0451
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs are not present
None

P0451 (Noise Monitor): 
Atmospheric pressure
70 kPa (525 mmHg) to 110 kPa (825 mmHg)
Battery voltage
10.5 V or more
Intake air temperature
4.4 to 35°C (40 to 95°F)
EVAP pressure sensor malfunction (P0452, P0453)
Not detected
Either of the following conditions is met:
A or B
A. Engine
Running
B. Soak time (power switch off time)
5 hours

Example of restart time 
First time
7 hours
Second time
9 hours and 30 minutes

P0451 (Stuck Monitor): 
Atmospheric pressure
Less than 70 kPa (525 mmHg) or 110 kPa (825 mmHg) or more
Battery voltage
10.5 V or more
Intake air temperature
4.4 to 35°C (40 to 95°F)
EVAP pressure sensor malfunction (P0452, P0453)
Not detected
Soak time (power switch off time)
5 hours

Example of restart time 
First time
7 hours
Second time
9 hours and 30 minutes

P0452 and P0453: 
The monitor will run whenever these DTCs are not present
None
Battery voltage
8 V or more
Power switch
ON

TYPICAL MALFUNCTION THRESHOLDS


1. P0451: Pressure sensor noise 
Frequency that EVAP pressure change is 0.3 kPa or more
10 times or more in 10 seconds

2. P0451: Pressure sensor stuck 
EVAP pressure change during reference pressure measurement
Less than 0.65 kPa (4.87 mmHg)

3. P0452: Pressure sensor low voltage 
EVAP Pressure
Less than 42.11 kPa (315.82 mmHg)

4. P0453: Pressure sensor high voltage 
EVAP Pressure
More than 123.761 kPa (928.207 mmHg)

WIRING DIAGRAM


A179772E01


INSPECTION PROCEDURE

NOTICE:
  1. When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel tank cap.
  2. Do not disassemble the canister pump module.
  3. The Techstream is required to conduct the following diagnostic troubleshooting procedure.

1.CONFIRM DTC AND EVAP PRESSURE
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / EVAP / Vapor Pressure Tank.

  1. Read the EVAP (Evaporative Emission) pressure displayed on the Techstream.

    Result:

    Display (DTC Output)
    Test Result
    Suspected Trouble Area
    Proceed to
    P0451
    -
    Pressure sensor
    C
    P0452
    Less than 45 kPa (338 mmHg)
    1. Wire harness/connector (hybrid vehicle control ECU - pressure sensor)
    2. Pressure sensor
    3. Short in ECM (included in hybrid vehicle control ECU) circuit
    A
    P0453
    More than 120 kPa (900 mmHg)
    1. Wire harness/connector (hybrid vehicle control ECU - pressure sensor)
    2. Pressure sensor
    3. Open in ECM (included in hybrid vehicle control ECU) circuit
    B



B
Go to step 4

C
GO TO EVAP INSPECTION PROCEDURE
A


2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - HYBRID VEHICLE CONTROL ECU)


    A107143E11
  1. Turn the power switch off.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance between the PPMP terminal of the hybrid vehicle control ECU connector and body ground.

    Result:
    Test Result
    Suspected Trouble Area
    Proceed to
    10 Ω or less
    1. Wire harness/connector (hybrid vehicle control ECU - pressure sensor)
    2. Short in pressure sensor circuit
    A
    10 kΩ or more
    1. Wire harness/connector (hybrid vehicle control ECU - pressure sensor)
    2. Short in ECM (included in hybrid vehicle control ECU) circuit
    B

  1. Reconnect the hybrid vehicle control ECU connector.



B
Go to step 7
A


3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - HYBRID VEHICLE CONTROL ECU)


    A172435E02
  1. Disconnect the canister pump module connector.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance between the PPMP terminal of the hybrid vehicle control ECU connector and body ground.

    Result:
    Test Result
    Suspected Trouble Area
    Proceed to
    10 kΩ or more
    Short in pressure sensor circuit
    A
    10 Ω or less
    Short in wire harness/connector (hybrid vehicle control ECU - pressure sensor)
    B

  1. Reconnect the canister pump module connector.

  1. Reconnect the hybrid vehicle control ECU connector.



A
Go to step 5

B
Go to step 6

4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - HYBRID VEHICLE CONTROL ECU)


    A172436E02
  1. Disconnect the canister pump module connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard:
    Tester Connection
    Condition
    Specified Condition
    O42-4 - Body ground
    Always
    4.5 to 5.0 V
    O42-3 - Body ground
    Always
    4.5 to 5.0 V
    O42-2 - Body ground
    Always
    100 Ω or less

    Result:
    Test Result
    Suspected Trouble Area
    Proceed to
    Voltage and resistance within standard ranges
    Open in pressure sensor circuit
    A
    Voltage and resistance outside standard ranges
    Open in wire harness/connector (hybrid vehicle control ECU - pressure sensor)
    B

  1. Reconnect the canister pump module connector.



A
Go to step 5

B
Go to step 6

5.REPLACE CHARCOAL CANISTER
  1. Replace the charcoal canister (Click here).



NEXT
Go to step 8

6.REPAIR OR REPLACE HARNESS OR CONNECTOR

HINT:
If the exhaust tail pipe has been removed, go to the next step before reinstalling it.



NEXT
Go to step 8

7.REPLACE HYBRID VEHICLE CONTROL ECU
  1. Replace the hybrid vehicle control ECU (Click here).



NEXT
Go to step 8

8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Wait for at least 60 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    HINT:
    If no pending DTC is displayed on the Techstream, the repair has been successfully completed.


NEXT

COMPLETED