Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0505    Idle Control System Malfunction

for Preparation Click here


DESCRIPTION

The idle speed is controlled by the electronic throttle control system. The electronic throttle control system is comprised of: 1) a one valve type throttle body; 2) the throttle actuator, which operates the throttle valve; 3) the throttle position sensor, which detects the opening angle of the throttle valve; 4) the accelerator pedal position sensor, which detects the accelerator pedal position; 5) the ECM (included in the hybrid vehicle control ECU), which controls the ETCS. Based on the target idle speed, the ECM controls the throttle actuator to provide the proper throttle valve opening angle.

DTC No.
DTC Detection Condition
Trouble Area
P0505
Idle speed continues to vary greatly from target speed (2 trip detection logic)
  1. ETCS
  2. Intake system
  3. PCV valve and hose
  4. PCV hose connection
  5. Hybrid vehicle control ECU

MONITOR DESCRIPTION

The ECM (included in the hybrid vehicle control ECU) monitors the idle speed and idle air flow volume to conduct Idle Speed Control (ISC). The ECM determines that the ISC system is malfunctioning if the following conditions are met:
  1. The learned idle air flow volume remains at the maximum or minimum 5 times or more during a driving cycle.
  2. While driving at 6 mph (10 km/h) or more, the actual engine idle speed varies from the target idle speed by between 100 rpm and 150 rpm, 5 times or more during a driving cycle.
Example:
If the actual idle speed varies from the target idle speed by more than 150 rpm* 5 times during a driving cycle, the ECM illuminates the MIL and sets the DTC.

HINT:
*: Threshold idle speed varies with engine load.


A082389E30


MONITOR STRATEGY


Related DTCs
P0505: ISC function
Required Sensors/Components (Main)
Electronic Throttle Control System
Required Sensors/Components (Related)
Crankshaft position sensor, Engine coolant temperature sensor, and Vehicle speed sensor
Frequency of Operation
Continuous
Duration
10 minutes
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs are not present
P0010, P0020 (VVT Oil Control Valve Bank 1, 2)
P0011, P0021 (VVT System 1 - Advance)
P0012, P0022 (VVT System 1 - Retard)
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio sensor heater - Sensor 1)
P0102, P0103 (Mass Air Flow meter)
P0115, P0117, P0118 (Engine Coolant Temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient Engine Coolant Temperature for Closed Loop)
P0171, P0172, P0174, P0175 (Fuel system)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0341, P0345, P0346 (VVT sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P0451, P0452, P0453, P1451, P1452, P1453 (EVAP system)
P2195, P2196, P2197, P2198 (Air Fuel Ratio sensor - rationality)
P2237, P2240 (Air fuel ratio sensor - open)
P2238, P2241, P2252, P2255 (Air fuel ratio sensor - low impedance)
P2239, P2242, P2253, P2256 (Air fuel ratio sensor - high impedance)
P2A00, P2A03 (Air Fuel Ratio sensor - slow response)

Functional check: 
Engine
Running

TYPICAL MALFUNCTION THRESHOLDS


Functional check: 
Either of following conditions 1 or 2 is met
-
1. Frequency that following conditions (a) and (b) are met
5 times or more
(a) Engine RPM - target engine RPM
Below -100 rpm, or more than 150 rpm
(b) Vehicle condition
Stop after vehicle was driven at 10 km/h (6.25 mph) or more
2. Frequency that following conditions (a) and (b) are met
Once
(a) Engine RPM - target engine RPM
Below -100 rpm, or 150 rpm or more
(b) ISC airflow rate (learning value)
1.3 L/sec. or less. or 9.24 L/sec. or more

INSPECTION PROCEDURE

HINT:
  1. The following condition may also cause DTC P0505 to be set:
    - The throttle valve is not fully closed. (e.g. The accelerator pedal is slightly depressed by something such as a floor mat overlapping the accelerator pedal.)
  2. Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0505)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following the menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC output)
    Proceed to
    P0505
    A
    P0505 and other DTCs
    B

    HINT:
    If any DTCs other than P0505 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.CHECK PCV HOSE CONNECTIONS

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks.

    OK:
    No leaks in intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


4.CHECK THROTTLE VALVE
  1. Check the throttle valve condition.

    OK:
    No foreign objects between the throttle valve and housing.



NG
REPLACE THROTTLE BODY ASSEMBLY (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)