Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0560    System Voltage

for Preparation Click here


DESCRIPTION

The auxiliary battery supplies electricity to the ECM (included in the hybrid vehicle control ECU) even when the power switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, these memories are cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM will illuminate the MIL and set the DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0560
Open in ECM (included in the hybrid vehicle control ECU) back-up power source circuit
(1 trip detection logic)
  1. Open in back-up power source circuit
  2. EFI No. 1 fuse
  3. Hybrid vehicle control ECU

HINT:
If DTC P0560 is set, the ECM (included in the hybrid vehicle control ECU) does not store other DTCs.


MONITOR STRATEGY


Related DTCs
P0560: ECM (included in the hybrid vehicle control ECU) system voltage
Required Sensors/Components (Main)
ECM (included in the hybrid vehicle control ECU)
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
3 seconds
MIL Operation
Immediate (MIL illuminated after next engine start)
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
Stand-by RAM
Initialized

TYPICAL MALFUNCTION THRESHOLDS


ECM (included in the hybrid vehicle control ECU) power source
Less than 3.5 V

WIRING DIAGRAM


A172448E02


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK FUSE (EFI NO. 1 FUSE)


    A179777E09
  1. Remove the EFI NO. 1 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the EFI NO. 1 fuse.



NG
REPLACE FUSE (EFI NO. 1 FUSE)
OK


2.INSPECT HYBRID VEHICLE CONTROL ECU (BATT VOLTAGE)


    A178695E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D35-1 (BATT) - B3-5 (E1)
    Always
    11 to 14 V



NG
Go to step 3
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - EFI NO. 1 FUSE)


    A172447E03
  1. Remove the EFI NO. 1 fuse from the engine room relay block.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    EFI NO. 1 fuse (2) - D35-1 (BATT)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    EFI NO. 1 fuse (2) or D35-1 (BATT) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the hybrid vehicle control ECU connector.

  1. Reinstall the EFI NO. 1 fuse.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (HYBRID VEHICLE CONTROL ECU - EFI NO. 1 FUSE)
OK


4.CHECK HARNESS AND CONNECTOR (EFI NO. 1 FUSE - BATTERY)


    A179782E02
  1. Remove the EFI NO. 1 fuse from the engine room relay.

  1. Disconnect the positive battery terminal.

  1. Measure the resistance according to the value(s) in the table below

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    Battery positive terminal - 1 (EFI NO. 1 fuse)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    Battery positive terminal or 1 (EFI NO. 1 fuse) - Body ground
    10 kΩ or higher

  1. Reconnect the positive battery terminal.

  1. Reinstall the EFI NO. 1 fuse.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI NO. 1 FUSE - BATTERY)
OK


5.INSPECT AUXILIARY BATTERY


NG
REPLACE AUXILIARY BATTERY
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)