Home › BODY › SLIDING ROOF › SLIDING ROOF SYSTEM

SLIDING ROOF SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG).

  3. Read the Data List according to the display on the Techstream.

    Slide Roof: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Open Switch
    Slide switch open signal/ON or OFF
    ON: OPEN switch is pressed.
    OFF: OPEN switch is not pressed.
    -
    Close Switch
    Slide switch close signal/ON or OFF
    ON: CLOSE switch is pressed.
    OFF: CLOSE switch is not pressed.
    -
    Up Switch
    Tilt switch up signal/ON or OFF
    ON: UP switch is pressed.
    OFF: UP switch is not pressed.
    -
    Down Switch
    Tilt switch down signal/ON or OFF
    ON: DOWN switch is pressed.
    OFF: DOWN switch is not pressed.
    -
    Hall IC1 Pulse
    Sliding roof operation signal/LO or HI
    LO: Sliding roof motor is not operating.
    HI: Sliding roof motor is operating.
    -
    Hall IC1 Status
    Sliding roof operation signal/NORMAL or LOCK
    NORMAL: Sliding roof motor is operating.
    LOCK: Sliding roof motor is not operating.
    -
    Hall IC2 Pulse
    Sliding roof operation signal/LO or HI
    LO: Sliding roof motor is not operating.
    HI: Sliding roof motor is operating.
    -
    Hall IC2 Status
    Sliding roof operation signal/NORMAL or LOCK
    NORMAL: Sliding roof motor is operating.
    LOCK: Sliding roof motor is not operating.
    -
    Ignition (Direct Signal)
    Power switch signal/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    Ignition (MPX)
    Power switch signal (MPX signal)/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    Door Courtesy
    Driver's door courtesy light switch signal/ON or OFF
    ON: Driver's side door is open.
    OFF: Driver's side door is closed.
    -
    Key Off Permission
    Key-OFF sliding roof operation permit signal (Current)/ON or OFF
    ON: Driver's side door is not closed within 45 sec. after power switch is turned off.
    OFF: Any status except "ON" status
    -
    Open Switch Failure (Past)
    Open switch failure signal (Past)/Fail or Not Fail
    Fail: Sliding roof open signal failure (Past)
    Not Fail: Sliding roof open signal not fail (Past)
    -
    Close Switch Failure (Past)
    Close switch failure signal (Past)/Fail or Not Fail
    Fail: Sliding roof close signal failure (Past)
    Not Fail: Sliding roof close signal not fail (Past)
    -
    Up Switch Failure (Past)
    Up switch failure signal (Past)/Fail or Not Fail
    Fail: Sliding roof tilt up signal failure (Past)
    Not Fail: Sliding roof tilt up signal not fail (Past)
    -
    Down Switch Failure (Past)
    Down switch failure signal (Past)/Fail or Not Fail
    Fail: Sliding roof tilt down signal failure (Past)
    Not Fail: Sliding roof tilt down signal not fail (Past)
    -
    Open Switch Failure (Current)
    Open switch failure signal (Current)/Fail or Not Fail
    Fail: Sliding roof open signal failure (Current)
    Not Fail: Sliding roof open signal not fail (Current)
    -
    Close Switch Failure (Current)
    Close switch failure signal (Current)/Fail or Not Fail
    Fail: Sliding roof close signal failure (Current)
    Not Fail: Sliding roof close signal not fail (Current)
    -
    Up Switch Failure (Current)
    Up switch failure signal (Current)/Fail or Not Fail
    Fail: Sliding roof tilt up signal failure (Current)
    Not Fail: Sliding roof tilt up signal not fail (Current)
    -
    Down Switch Failure (Current)
    Down switch failure signal (Current)/Fail or Not Fail
    Fail: Sliding roof tilt down signal failure (Current)
    Not Fail: Sliding roof tilt down signal not fail (Current)
    -
    Number of Trouble code
    Number of trouble code
    Number of trouble code
    -


PERFORM ACTIVE TEST

HINT:
Performing the Techstream's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed during the Active Test.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG).

  3. Perform the Active Test according to the display on the Techstream.

    Slide Roof: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Slide Roof
    Operate sliding roof SLIDE CLOSE/TILT UP
    Clos/Up: Sliding roof SLIDE CLOSE or TILT UP operation occurs.
    OFF: Sliding roof is not operating
    -
    Slide Roof
    Operate sliding roof SLIDE OPEN/TILT DOWN
    Opn/Dwn: Sliding roof SLIDE OPEN or TILT DOWN operation occurs
    OFF: Sliding roof is not operating
    -