Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat)

FRONT SEAT ASSEMBLY (for Manual Seat) > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT SEAT WIRE RH (for Front Passenger Side)
  1. Engage the each clamps and install the front seat wire RH.



2. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)


    C165115
  1. Install the occupant classification ECU with the claw.

    NOTICE:
    1. If the occupant classification ECU has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the occupant classification ECU with a new one.
    2. When installing the occupant classification ECU, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Connect the 2 connectors.



3. INSTALL SEAT POSITION SENSOR


    C168034
  1. Install the seat position sensor to the seat slide position sensor protector with the pin as shown in the illustration.



    C107067E10
  1. Using a 1.3 mm (0.051 in.) feeler gauge, temporarily install the seat position sensor.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    HINT:
    Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).



    C166974
  1. Using a "TORX" socket wrench (T30), tighten the "TORX" screw to install the seat position sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).

  1. Connect the connector.

  1. Check that there are no loose parts after installing the seat position sensor.



4. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (for Front Passenger Side)


    B176349
  1. w/ Seat Heater System:
    Engage the 2 clamps and install the seat heater control sub-assembly.



5. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH


    B174617
  1. Engage the guide and the claw.

  1. Install the front seat lower cushion shield RH with the screw.



6. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH


    B174616
  1. Engage the claw.

  1. Install the front seat lower cushion shield LH with the screw.



7. INSTALL RECLINING ADJUSTER INSIDE COVER RH


    B174610
  1. Engage the claw.

  1. Install the reclining adjuster inside cover RH with the screw.



8. INSTALL RECLINING ADJUSTER INSIDE COVER RH


    B174608
  1. Engage the guide.

  1. Install the reclining adjuster inside cover RH with the screw.



9. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    B174609
  1. Engage the claw.

  1. Install the reclining adjuster inside cover LH with the screw.



10. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    B174607E01
  1. Engage the guide.

  1. Engage the clamp.

  1. Install the reclining adjuster inside cover LH with the screw.



11. INSTALL ACTIVE HEADREST LOWER UNIT


    B176346
  1. Install the active headrest lower unit with the 4 nuts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



12. INSTALL ACTIVE HEADREST UPPER UNIT


    B176345
  1. Install the active headrest upper unit with the 4 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the cable to the active headrest upper unit with the nut as shown in the illustration.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



13. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    B173750E01
  1. Using hog ring pliers, install the separate type front seatback cover with 7 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



14. INSTALL FRONT SEATBACK COVER WITH PAD
  1. Temporarily install the front seatback cover with pad to the front seat frame assembly with adjuster.



    B172866
  1. Engage the 4 claws and install the 2 front seat headrest supports.



    B174631E01
  1. Install the front seatback cover bracket with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.
    2. Check that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.



    B174634E01
  1. Using hog ring pliers, install 5 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B174635E01
  1. Using hog ring pliers, install the front seatback cover with pad with 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



15. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    B173751E01
  1. Using hog ring pliers, install the separate type front seat cushion cover with 11 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B173749E01
  1. Using hog ring pliers, install the separate type front seat cushion cover with 6 new hog rings.



16. INSTALL FRONT SEAT CUSHION COVER WITH PAD
  1. Temporarily install the front seat cushion cover with pad to the front seat frame assembly with adjuster.



  1. Engage the hooks.


    B174636

  1. Install the front seat cushion cover with pad with the 2 clips.

  1. for Front Passenger Side:

    1. w/ Seat Heater System:
      Connect the seat heater connector.



    B174625
  1. Engage the clamp.



17. INSTALL FRONT SEAT CUSHION INNER SHIELD


    B174637
  1. Insert the guide and temporarily install the front seat cushion inner shield.



    B174623
  1. Engage the claw.

  1. Install the front seat cushion inner shield with the screw.



18. INSTALL FRONT SEAT INNER BELT ASSEMBLY


    B170883E01
  1. Install the front seat inner belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

  1. Connect each connector and clamp.



19. INSTALL FRONT SEAT CUSHION SHIELD


    B174606
  1. Engage the 2 guides.

  1. Engage the claw.

  1. Install the front seat cushion shield with the 3 screws.



    B180387
  1. Engage the hooks.



20. INSTALL VERTICAL ADJUSTING HANDLE


    B174605
  1. Install the vertical adjusting handle with the 2 screws.



21. INSTALL VERTICAL ADJUSTER COVER


    B174619
  1. Engage the 2 claws and install the vertical adjuster cover.



22. INSTALL RECLINING ADJUSTER RELEASE HANDLE


    B174618
  1. Engage the claw and install the reclining adjuster release handle.



23. INSTALL VERTICAL SEAT ADJUSTER KNOB


    B174622E01
  1. Install the snap ring to the vertical seat adjuster knob as shown in the illustration.

  1. Install the vertical seat adjuster knob.