Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor Circuit Malfunction

DTC    P0341    Camshaft Position Sensor "A" Circuit Range / Performance (Bank 1 or Single Sensor)

DTC    P0345    Camshaft Position Sensor "A" Circuit (Bank 2)

DTC    P0346    Camshaft Position Sensor "A" Circuit Range / Performance (Bank 2)

for Preparation Click here


DESCRIPTION

The VVT (Variable Valve Timing) sensor (G signal) consists of a magnet, iron core and pickup coil.
The G signal plate has a 3 teeth on its outer circumference and is installed on the camshaft timing pulley. When the camshaft rotate, the protrusion on the signal plate and the air gap on the pickup coil change, causing fluctuations in the magnetic field and generating a voltage in the pickup coil.
This sensor monitors a timing rotor located on the camshaft and is used to detect a camshaft angle by the ECM (included in the hybrid vehicle control ECU). The camshaft rotation synchronizes with the crankshaft rotation, and this sensor communicates the rotation of the camshaft rotor as a pulse signal to the ECM. Based on the signal, the ECM controls fuel injection timing and ignition timing.

DTC No.
DTC Detection Condition
Trouble Area
P0340
P0345
  1. No VVT sensor signal to ECM (included in the hybrid vehicle control ECU) during cranking.
    (1 trip detection logic)
  2. No VVT sensor signal to ECM (included in the hybrid vehicle control ECU) with engine speed 600 rpm or more.
    (1 trip detection logic)
  1. Open or short in VVT sensor
  2. VVT sensor
  3. Camshaft timing gear
  4. Hybrid vehicle control ECU
P0341
While crankshaft rotates twice, VVT sensor signal is input to ECM (included in the hybrid vehicle control ECU) 12 times or more.
(1 trip detection logic)
  1. Open or short in VVT sensor
  2. VVT sensor
  3. Camshaft timing gear
  4. Hybrid vehicle control ECU
P0346
While crankshaft rotates twice, VVT sensor signal is input to ECM (included in the hybrid vehicle control ECU) 12 times or more.
(1 trip detection logic)
  1. Open or short in VVT sensor
  2. VVT sensor
  3. Camshaft timing gear
  4. Hybrid vehicle control ECU
Reference: Inspection using an oscilloscope
A110929E01

HINT:
  1. The correct waveform is as shown in the illustration.
  2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.


Item
Content
Terminals
NE+ - NE-
VV1+ - NE-
VV2+ - NE-
Equipment Settings
5 V/Division, 20 ms/Division
Conditions
Cranking or idling

MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine rotating, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM (included in the hybrid vehicle control ECU) interprets this as a malfunction of the sensor.

MONITOR STRATEGY


Related DTCs
P0340: VVT position/Crankshaft position misalignment (Bank 1)
P0341: Camshaft position sensor (Bank 1) malfunction
P0345: VVT sensor (Bank 2) range check
P0346: VVT sensor (Bank 2) malfunction
Required Sensors/Components (Main)
VVT position sensor (Bank 1 and 2)
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
5 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs are not present
None

P0340: 
Engine speed
600 rpm or more
Starter
OFF

P0341: 
Engine revolution angle
720 °CA

P0345: 
Engine speed
600 rpm or more
Battery voltage
8 V or more
Power switch
ON

P0346: 
Engine revolution angle
720 °CA

TYPICAL MALFUNCTION THRESHOLDS


P0340: 
Camshaft position and crankshaft position alignment
Misaligned

P0341: 
Camshaft position and crankshaft position alignment
Misaligned
Camshaft position signal count
12 signals or more

P0345: 
VVT sensor signal
No signal

P0346: 
VVT sensor signal count
12 signals or more

COMPONENT OPERATING RANGE


VVT sensor voltage
Camshaft position sensor voltage fluctuates when the crankshaft rotating
3 camshaft position signals per 1 revolution camshaft
3 camshaft position signals per 2 revolutions camshaft

WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ECU TERMINAL VOLTAGE (VV1+, VV2+, NE+ AND NE- TERMINALS)


    A110930E09
  1. Inspect the hybrid vehicle control ECU using an oscilloscope.

    1. While the engine is idling, check the waveform between the terminals of the hybrid vehicle control ECU connector.

      Standard:
      Tester Connection
      Condition
      Specified Condition
      B3-27 (VV1+) - B3-24 (NE-)
      Idling
      Correct waveform shown
      B3-26 (VV2+) - B3-24 (NE-)
      Idling
      Correct waveform shown
      B3-25 (NE+) - B3-24 (NE-)
      Idling
      Correct waveform shown



NG
Go to step 2
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

2.CHECK VVT SENSOR (SENSOR RESISTANCE)


    A178651E04
  1. Disconnect the VVT sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    950 to 1250 Ω

  1. Reconnect the VVT sensor connector.



NG
REPLACE VVT SENSOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (VVT SENSOR - HYBRID VEHICLE CONTROL ECU)


    A178678E03
  1. Disconnect the VVT sensor connector.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B22-1 (VVT sensor) - B3-27 (VV1+)
    Always
    Below 1 Ω
    B22-2 (VVT sensor) - B3-24 (NE-)
    Always
    Below 1 Ω
    B23-1 (VVT sensor) - B3-26 (VV2+)
    Always
    Below 1 Ω
    B23-2 (VVT sensor) - B3-24 (NE-)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B22-1 (VVT sensor) or B3-27 (VV1+) - Body ground
    Always
    10 kΩ or higher
    B22-2 (VVT sensor) or B3-24 (NE-) - Body ground
    Always
    10 kΩ or higher
    B23-1 (VVT sensor) or B3-26 (VV2+) - Body ground
    Always
    10 kΩ or higher
    B23-2 (VVT sensor) or B3-24 (NE-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the VVT sensor connector.

  1. Reconnect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK SENSOR INSTALLATION (VVT SENSOR)


    BR03795E54
  1. Check the VVT sensor installation.

    OK:
    Sensor is installed correctly.



NG
REPAIR OR REPLACE VVT
OK


5.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)
  1. Check the teeth of the signal plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)